lpc32xx: add Ethernet support

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>

arch/arm/cpu/arm926ejs/lpc32xx/cpu.c

@@ -5,6 +5,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/wdt.h>
@@ -55,3 +56,11 @@ int print_cpuinfo(void)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_LPC32XX_ETH
+int cpu_eth_init(bd_t *bis)
+{
+	lpc32xx_eth_initialize(bis);
+	return 0;
+}
+#endif

arch/arm/cpu/arm926ejs/lpc32xx/devices.c

@@ -37,3 +37,10 @@ void lpc32xx_uart_init(unsigned int uart_id)
 	writel(CLK_UART_X_DIV(1) | CLK_UART_Y_DIV(1),
 	       &clk->u3clk + (uart_id - 3));
 }
+
+void lpc32xx_mac_init(void)
+{
+	/* Enable MAC interface */
+	writel(CLK_MAC_REG | CLK_MAC_SLAVE | CLK_MAC_MASTER
+		| CLK_MAC_MII, &clk->macclk_ctrl);
+}

arch/arm/include/asm/arch-lpc32xx/config.h

@@ -52,6 +52,9 @@
 #define CONFIG_SYS_BAUDRATE_TABLE	\
 		{ 9600, 19200, 38400, 57600, 115200, 230400, 460800 }
 
+/* Ethernet */
+#define LPC32XX_ETH_BASE ETHERNET_BASE
+
 /* NOR Flash */
 #if defined(CONFIG_SYS_FLASH_CFI)
 #define CONFIG_FLASH_CFI_DRIVER

arch/arm/include/asm/arch-lpc32xx/sys_proto.h

@@ -8,5 +8,6 @@
 #define _LPC32XX_SYS_PROTO_H
 
 void lpc32xx_uart_init(unsigned int uart_id);
+void lpc32xx_mac_init(void);
 
 #endif /* _LPC32XX_SYS_PROTO_H */

drivers/net/Makefile

@@ -35,6 +35,7 @@ obj-$(CONFIG_GRETH) += greth.o
 obj-$(CONFIG_DRIVER_TI_KEYSTONE_NET) += keystone_net.o
 obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o
 obj-$(CONFIG_LAN91C96) += lan91c96.o
+obj-$(CONFIG_LPC32XX_ETH) += lpc32xx_eth.o
 obj-$(CONFIG_MACB) += macb.o
 obj-$(CONFIG_MCFFEC) += mcffec.o mcfmii.o
 obj-$(CONFIG_MPC5xxx_FEC) += mpc5xxx_fec.o

drivers/net/lpc32xx_eth.c

+/*
+ * LPC32xx Ethernet MAC interface driver
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD - 3ADEV <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <net.h>
+#include <malloc.h>
+#include <miiphy.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/types.h>
+#include <asm/system.h>
+#include <asm/byteorder.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/config.h>
+
+/*
+ * Notes:
+ *
+ * 1. Unless specified otherwise, all references to tables or paragraphs
+ *    are to UM10326, "LPC32x0 and LPC32x0/01 User manual".
+ *
+ * 2. Only bitfield masks/values which are actually used by the driver
+ *    are defined.
+ */
+
+/* a single RX descriptor. The controller has an array of these */
+struct lpc32xx_eth_rxdesc {
+	u32 packet;		/* Receive packet pointer */
+	u32 control;		/* Descriptor command status */
+};
+
+#define LPC32XX_ETH_RX_DESC_SIZE (sizeof(struct lpc32xx_eth_rxdesc))
+
+/* RX control bitfields/masks (see Table 330) */
+#define LPC32XX_ETH_RX_CTRL_SIZE_MASK 0x000007FF
+#define LPC32XX_ETH_RX_CTRL_UNUSED    0x7FFFF800
+#define LPC32XX_ETH_RX_CTRL_INTERRUPT 0x80000000
+
+/* a single RX status. The controller has an array of these */
+struct lpc32xx_eth_rxstat {
+	u32 statusinfo;		/* Transmit Descriptor status */
+	u32 statushashcrc;	/* Transmit Descriptor CRCs */
+};
+
+#define LPC32XX_ETH_RX_STAT_SIZE (sizeof(struct lpc32xx_eth_rxstat))
+
+/* RX statusinfo bitfields/masks (see Table 333) */
+#define RX_STAT_RXSIZE 0x000007FF
+/* Helper: OR of all errors except RANGE */
+#define RX_STAT_ERRORS 0x1B800000
+
+/* a single TX descriptor. The controller has an array of these */
+struct lpc32xx_eth_txdesc {
+	u32 packet;		/* Transmit packet pointer */
+	u32 control;		/* Descriptor control */
+};
+
+#define LPC32XX_ETH_TX_DESC_SIZE (sizeof(struct lpc32xx_eth_txdesc))
+
+/* TX control bitfields/masks (see Table 335) */
+#define TX_CTRL_TXSIZE    0x000007FF
+#define TX_CTRL_LAST      0x40000000
+
+/* a single TX status. The controller has an array of these */
+struct lpc32xx_eth_txstat {
+	u32 statusinfo;		/* Transmit Descriptor status */
+};
+
+#define LPC32XX_ETH_TX_STAT_SIZE (sizeof(struct lpc32xx_eth_txstat))
+
+/* Ethernet MAC interface registers (see Table 283) */
+struct lpc32xx_eth_registers {
+	/* MAC registers - 0x3106_0000 to 0x3106_01FC */
+	u32 mac1;		/* MAC configuration register 1 */
+	u32 mac2;		/* MAC configuration register 2 */
+	u32 ipgt;		/* Back-to-back Inter-Packet Gap reg. */
+	u32 ipgr;		/* Non-back-to-back IPG register */
+	u32 clrt;		/* Collision Window / Retry register */
+	u32 maxf;		/* Maximum Frame register */
+	u32 supp;		/* Phy Support register */
+	u32 test;
+	u32 mcfg;		/* MII management configuration reg. */
+	u32 mcmd;		/* MII management command register */
+	u32 madr;		/* MII management address register */
+	u32 mwtd;		/* MII management wite data register */
+	u32 mrdd;		/* MII management read data register */
+	u32 mind;		/* MII management indicators register */
+	u32 reserved1[2];
+	u32 sa0;		/* Station address register 0 */
+	u32 sa1;		/* Station address register 1 */
+	u32 sa2;		/* Station address register 2 */
+	u32 reserved2[45];
+	/* Control registers */
+	u32 command;
+	u32 status;
+	u32 rxdescriptor;
+	u32 rxstatus;
+	u32 rxdescriptornumber;	/* actually, number MINUS ONE */
+	u32 rxproduceindex;	/* head of rx desc fifo */
+	u32 rxconsumeindex;	/* tail of rx desc fifo */
+	u32 txdescriptor;
+	u32 txstatus;
+	u32 txdescriptornumber;	/* actually, number MINUS ONE */
+	u32 txproduceindex;	/* head of rx desc fifo */
+	u32 txconsumeindex;	/* tail of rx desc fifo */
+	u32 reserved3[10];
+	u32 tsv0;		/* Transmit status vector register 0 */
+	u32 tsv1;		/* Transmit status vector register 1 */
+	u32 rsv;		/* Receive status vector register */
+	u32 reserved4[3];
+	u32 flowcontrolcounter;
+	u32 flowcontrolstatus;
+	u32 reserved5[34];
+	/* RX filter registers - 0x3106_0200 to 0x3106_0FDC */
+	u32 rxfilterctrl;
+	u32 rxfilterwolstatus;
+	u32 rxfilterwolclear;
+	u32 reserved6;
+	u32 hashfilterl;
+	u32 hashfilterh;
+	u32 reserved7[882];
+	/* Module control registers - 0x3106_0FE0 to 0x3106_0FF8 */
+	u32 intstatus;		/* Interrupt status register */
+	u32 intenable;
+	u32 intclear;
+	u32 intset;
+	u32 reserved8;
+	u32 powerdown;
+	u32 reserved9;
+};
+
+/* MAC1 register bitfields/masks and offsets (see Table 283) */
+#define MAC1_RECV_ENABLE        0x00000001
+#define MAC1_PASS_ALL_RX_FRAMES 0x00000002
+#define MAC1_SOFT_RESET         0x00008000
+/* Helper: general reset */
+#define MAC1_RESETS             0x0000CF00
+
+/* MAC2 register bitfields/masks and offsets (see Table 284) */
+#define MAC2_FULL_DUPLEX    0x00000001
+#define MAC2_CRC_ENABLE     0x00000010
+#define MAC2_PAD_CRC_ENABLE 0x00000020
+
+/* SUPP register bitfields/masks and offsets (see Table 290) */
+#define SUPP_SPEED 0x00000100
+
+/* MCFG register bitfields/masks and offsets (see Table 292) */
+#define MCFG_CLOCK_SELECT_MASK  0x0000001C
+/* divide clock by 28 (see Table 293) */
+#define MCFG_CLOCK_SELECT_DIV28 0x0000001C
+
+/* MADR register bitfields/masks and offsets (see Table 295) */
+#define MADR_REG_MASK   0x0000001F
+#define MADR_PHY_MASK   0x00001F00
+#define MADR_REG_OFFSET 0
+#define MADR_PHY_OFFSET 8
+
+/* MIND register bitfields/masks (see Table 298) */
+#define MIND_BUSY      0x00000001
+
+/* COMMAND register bitfields/masks and offsets (see Table 283) */
+#define COMMAND_RXENABLE      0x00000001
+#define COMMAND_TXENABLE      0x00000002
+#define COMMAND_PASSRUNTFRAME 0x00000040
+#define COMMAND_FULL_DUPLEX   0x00000400
+/* Helper: general reset */
+#define COMMAND_RESETS        0x0000001C
+
+/* STATUS register bitfields/masks and offsets (see Table 283) */
+#define STATUS_RXSTATUS 0x00000001
+#define STATUS_TXSTATUS 0x00000002
+
+/* RXFILTERCTRL register bitfields/masks (see Table 319) */
+#define RXFILTERCTRL_ACCEPTBROADCAST 0x00000002
+#define RXFILTERCTRL_ACCEPTPERFECT   0x00000020
+
+/* Buffers and descriptors */
+
+#define ATTRS(n) __aligned(n)
+
+#define TX_BUF_COUNT 4
+#define RX_BUF_COUNT 4
+
+struct lpc32xx_eth_buffers {
+	ATTRS(4) struct lpc32xx_eth_txdesc tx_desc[TX_BUF_COUNT];
+	ATTRS(4) struct lpc32xx_eth_txstat tx_stat[TX_BUF_COUNT];
+	ATTRS(PKTALIGN) u8 tx_buf[TX_BUF_COUNT*PKTSIZE_ALIGN];
+	ATTRS(4) struct lpc32xx_eth_rxdesc rx_desc[RX_BUF_COUNT];
+	ATTRS(8) struct lpc32xx_eth_rxstat rx_stat[RX_BUF_COUNT];
+	ATTRS(PKTALIGN) u8 rx_buf[RX_BUF_COUNT*PKTSIZE_ALIGN];
+};
+
+/* port device data struct */
+struct lpc32xx_eth_device {
+	struct eth_device dev;
+	struct lpc32xx_eth_registers *regs;
+	struct lpc32xx_eth_buffers *bufs;
+};
+
+#define LPC32XX_ETH_DEVICE_SIZE (sizeof(struct lpc32xx_eth_device))
+
+/* generic macros */
+#define to_lpc32xx_eth(_d) container_of(_d, struct lpc32xx_eth_device, dev)
+
+/* timeout for MII polling */
+#define MII_TIMEOUT 10000000
+
+/* limits for PHY and register addresses */
+#define MII_MAX_REG (MADR_REG_MASK >> MADR_REG_OFFSET)
+
+#define MII_MAX_PHY (MADR_PHY_MASK >> MADR_PHY_OFFSET)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if defined(CONFIG_PHYLIB) || defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
+/*
+ * mii_reg_read - miiphy_read callback function.
+ *
+ * Returns 16bit phy register value, or 0xffff on error
+ */
+static int mii_reg_read(const char *devname, u8 phy_adr, u8 reg_ofs, u16 *data)
+{
+	struct eth_device *dev = eth_get_dev_by_name(devname);
+	struct lpc32xx_eth_device *dlpc32xx_eth = to_lpc32xx_eth(dev);
+	struct lpc32xx_eth_registers *regs = dlpc32xx_eth->regs;
+	u32 mind_reg;
+	u32 timeout;
+
+	/* check parameters */
+	if (phy_adr > MII_MAX_PHY) {
+		printf("%s:%u: Invalid PHY address %d\n",
+		       __func__, __LINE__, phy_adr);
+		return -EFAULT;
+	}
+	if (reg_ofs > MII_MAX_REG) {
+		printf("%s:%u: Invalid register offset %d\n",
+		       __func__, __LINE__, reg_ofs);
+		return -EFAULT;
+	}
+
+	/* write the phy and reg addressse into the MII address reg */
+	writel((phy_adr << MADR_PHY_OFFSET) | (reg_ofs << MADR_REG_OFFSET),
+	       &regs->madr);
+
+	/* write 1 to the MII command register to cause a read */
+	writel(1, &regs->mcmd);
+
+	/* wait till the MII is not busy */
+	timeout = MII_TIMEOUT;
+	do {
+		/* read MII indicators register */
+		mind_reg = readl(&regs->mind);
+		if (--timeout == 0)
+			break;
+	} while (mind_reg & MIND_BUSY);
+
+	/* write 0 to the MII command register to finish the read */
+	writel(0, &regs->mcmd);
+
+	if (timeout == 0) {
+		printf("%s:%u: MII busy timeout\n", __func__, __LINE__);
+		return -EFAULT;
+	}
+
+	*data = (u16) readl(&regs->mrdd);
+
+	debug("%s:(adr %d, off %d) => %04x\n", __func__, phy_adr,
+	      reg_ofs, *data);
+
+	return 0;
+}
+
+/*
+ * mii_reg_write - imiiphy_write callback function.
+ *
+ * Returns 0 if write succeed, -EINVAL on bad parameters
+ * -ETIME on timeout
+ */
+static int mii_reg_write(const char *devname, u8 phy_adr, u8 reg_ofs, u16 data)
+{
+	struct eth_device *dev = eth_get_dev_by_name(devname);
+	struct lpc32xx_eth_device *dlpc32xx_eth = to_lpc32xx_eth(dev);
+	struct lpc32xx_eth_registers *regs = dlpc32xx_eth->regs;
+	u32 mind_reg;
+	u32 timeout;
+
+	/* check parameters */
+	if (phy_adr > MII_MAX_PHY) {
+		printf("%s:%u: Invalid PHY address %d\n",
+		       __func__, __LINE__, phy_adr);
+		return -EFAULT;
+	}
+	if (reg_ofs > MII_MAX_REG) {
+		printf("%s:%u: Invalid register offset %d\n",
+		       __func__, __LINE__, reg_ofs);
+		return -EFAULT;
+	}
+
+	/* wait till the MII is not busy */
+	timeout = MII_TIMEOUT;
+	do {
+		/* read MII indicators register */
+		mind_reg = readl(&regs->mind);
+		if (--timeout == 0)
+			break;
+	} while (mind_reg & MIND_BUSY);
+
+	if (timeout == 0) {
+		printf("%s:%u: MII busy timeout\n", __func__,
+		       __LINE__);
+		return -EFAULT;
+	}
+
+	/* write the phy and reg addressse into the MII address reg */
+	writel((phy_adr << MADR_PHY_OFFSET) | (reg_ofs << MADR_REG_OFFSET),
+	       &regs->madr);
+
+	/* write data to the MII write register */
+	writel(data, &regs->mwtd);
+
+	/*debug("%s:(adr %d, off %d) <= %04x\n", __func__, phy_adr,
+		reg_ofs, data);*/
+
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_PHYLIB)
+int lpc32xx_eth_phy_read(struct mii_dev *bus, int phy_addr, int dev_addr,
+	int reg_addr)
+{
+	u16 data;
+	int ret;
+	ret = mii_reg_read(bus->name, phy_addr, reg_addr, &data);
+	if (ret)
+		return ret;
+	return data;
+}
+
+int lpc32xx_eth_phy_write(struct mii_dev *bus, int phy_addr, int dev_addr,
+	int reg_addr, u16 data)
+{
+	return mii_reg_write(bus->name, phy_addr, reg_addr, data);
+}
+#endif
+
+/*
+ * Locate buffers in SRAM at 0x00001000 to avoid cache issues and
+ * maximize throughput.
+ */
+
+#define LPC32XX_ETH_BUFS 0x00001000
+
+static struct lpc32xx_eth_device lpc32xx_eth = {
+	.regs = (struct lpc32xx_eth_registers *)LPC32XX_ETH_BASE,
+	.bufs = (struct lpc32xx_eth_buffers *)LPC32XX_ETH_BUFS
+};
+
+#define TX_TIMEOUT 10000
+
+static int lpc32xx_eth_send(struct eth_device *dev, void *dataptr, int datasize)
+{
+	struct lpc32xx_eth_device *lpc32xx_eth_device =
+		container_of(dev, struct lpc32xx_eth_device, dev);
+	struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs;
+	struct lpc32xx_eth_buffers *bufs = lpc32xx_eth_device->bufs;
+	int timeout, tx_index;
+
+	/* time out if transmit descriptor array remains full too long */
+	timeout = TX_TIMEOUT;
+	while ((readl(&regs->status) & STATUS_TXSTATUS) &&
+	       (readl(&regs->txconsumeindex)
+	       == readl(&regs->txproduceindex))) {
+		if (timeout-- == 0)
+			return -1;
+	}
+
+	/* determine next transmit packet index to use */
+	tx_index = readl(&regs->txproduceindex);
+
+	/* set up transmit packet */
+	writel((u32)dataptr, &bufs->tx_desc[tx_index].packet);
+	writel(TX_CTRL_LAST | ((datasize - 1) & TX_CTRL_TXSIZE),
+	       &bufs->tx_desc[tx_index].control);
+	writel(0, &bufs->tx_stat[tx_index].statusinfo);
+
+	/* pass transmit packet to DMA engine */
+	tx_index = (tx_index + 1) % TX_BUF_COUNT;
+	writel(tx_index, &regs->txproduceindex);
+
+	/* transmission succeeded */
+	return 0;
+}
+
+#define RX_TIMEOUT 1000000
+
+static int lpc32xx_eth_recv(struct eth_device *dev)
+{
+	struct lpc32xx_eth_device *lpc32xx_eth_device =
+		container_of(dev, struct lpc32xx_eth_device, dev);
+	struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs;
+	struct lpc32xx_eth_buffers *bufs = lpc32xx_eth_device->bufs;
+	int timeout, rx_index;
+
+	/* time out if receive descriptor array remains empty too long */
+	timeout = RX_TIMEOUT;
+	while (readl(&regs->rxproduceindex) == readl(&regs->rxconsumeindex)) {
+		if (timeout-- == 0)
+			return -1;
+	}
+
+	/* determine next receive packet index to use */
+	rx_index = readl(&regs->rxconsumeindex);
+
+	/* if data was valid, pass it on */
+	if (!(bufs->rx_stat[rx_index].statusinfo & RX_STAT_ERRORS))
+		NetReceive(&(bufs->rx_buf[rx_index*PKTSIZE_ALIGN]),
+			   (bufs->rx_stat[rx_index].statusinfo
+			    & RX_STAT_RXSIZE) + 1);
+
+	/* pass receive slot back to DMA engine */
+	rx_index = (rx_index + 1) % RX_BUF_COUNT;
+	writel(rx_index, &regs->rxconsumeindex);
+
+	/* reception successful */
+	return 0;
+}
+
+static int lpc32xx_eth_write_hwaddr(struct eth_device *dev)
+{
+	struct lpc32xx_eth_device *lpc32xx_eth_device =
+		container_of(dev, struct lpc32xx_eth_device, dev);
+	struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs;
+
+	/* Save station address */
+	writel((unsigned long) (dev->enetaddr[0] |
+		(dev->enetaddr[1] << 8)), &regs->sa2);
+	writel((unsigned long) (dev->enetaddr[2] |
+		(dev->enetaddr[3] << 8)), &regs->sa1);
+	writel((unsigned long) (dev->enetaddr[4] |
+		(dev->enetaddr[5] << 8)), &regs->sa0);
+
+	return 0;
+}
+
+static int lpc32xx_eth_init(struct eth_device *dev)
+{
+	struct lpc32xx_eth_device *lpc32xx_eth_device =
+		container_of(dev, struct lpc32xx_eth_device, dev);
+	struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs;
+	struct lpc32xx_eth_buffers *bufs = lpc32xx_eth_device->bufs;
+	int index;
+
+	/* Release SOFT reset to let MII talk to PHY */
+	clrbits_le32(&regs->mac1, MAC1_SOFT_RESET);
+
+	/* Configure Full/Half Duplex mode */
+	if (miiphy_duplex(dev->name, CONFIG_PHY_ADDR) == FULL) {
+		setbits_le32(&regs->mac2, MAC2_FULL_DUPLEX);
+		setbits_le32(&regs->command, COMMAND_FULL_DUPLEX);
+		writel(0x15, &regs->ipgt);
+	} else {
+		writel(0x12, &regs->ipgt);
+	}
+
+	/* Configure 100MBit/10MBit mode */
+	if (miiphy_speed(dev->name, CONFIG_PHY_ADDR) == _100BASET)
+		writel(SUPP_SPEED, &regs->supp);
+	else
+		writel(0, &regs->supp);
+
+	/* Initial MAC initialization */
+	writel(MAC1_PASS_ALL_RX_FRAMES, &regs->mac1);
+	writel(MAC2_PAD_CRC_ENABLE | MAC2_CRC_ENABLE, &regs->mac2);
+	writel(PKTSIZE_ALIGN, &regs->maxf);
+
+	/* Retries: 15 (0xF). Collision window: 57 (0x37). */
+	writel(0x370F, &regs->clrt);
+
+	/* Set IP gap pt 2 to default 0x12 but pt 1 to non-default 0 */
+	writel(0x0012, &regs->ipgr);
+
+	/* pass runt (smaller than 64 bytes) frames */
+	writel(COMMAND_PASSRUNTFRAME, &regs->command);
+
+	/* Save station address */
+	writel((unsigned long) (dev->enetaddr[0] |
+		(dev->enetaddr[1] << 8)), &regs->sa2);
+	writel((unsigned long) (dev->enetaddr[2] |
+		(dev->enetaddr[3] << 8)), &regs->sa1);
+	writel((unsigned long) (dev->enetaddr[4] |
+		(dev->enetaddr[5] << 8)), &regs->sa0);
+
+	/* set up transmit buffers */
+	for (index = 0; index < TX_BUF_COUNT; index++) {
+		bufs->tx_desc[index].control = 0;
+		bufs->tx_stat[index].statusinfo = 0;
+	}
+	writel((u32)(&bufs->tx_desc), (u32 *)&regs->txdescriptor);
+	writel((u32)(&bufs->tx_stat), &regs->txstatus);
+	writel(TX_BUF_COUNT-1, &regs->txdescriptornumber);
+
+	/* set up receive buffers */
+	for (index = 0; index < RX_BUF_COUNT; index++) {
+		bufs->rx_desc[index].packet =
+			(u32) (bufs->rx_buf+index*PKTSIZE_ALIGN);
+		bufs->rx_desc[index].control = PKTSIZE_ALIGN - 1;
+		bufs->rx_stat[index].statusinfo = 0;
+		bufs->rx_stat[index].statushashcrc = 0;
+	}
+	writel((u32)(&bufs->rx_desc), &regs->rxdescriptor);
+	writel((u32)(&bufs->rx_stat), &regs->rxstatus);
+	writel(RX_BUF_COUNT-1, &regs->rxdescriptornumber);
+
+	/* Enable broadcast and matching address packets */
+	writel(RXFILTERCTRL_ACCEPTBROADCAST |
+		RXFILTERCTRL_ACCEPTPERFECT, &regs->rxfilterctrl);
+
+	/* Clear and disable interrupts */
+	writel(0xFFFF, &regs->intclear);
+	writel(0, &regs->intenable);
+
+	/* Enable receive and transmit mode of MAC ethernet core */
+	setbits_le32(&regs->command, COMMAND_RXENABLE | COMMAND_TXENABLE);
+	setbits_le32(&regs->mac1, MAC1_RECV_ENABLE);
+
+	/*
+	 * Perform a 'dummy' first send to work around Ethernet.1
+	 * erratum (see ES_LPC3250 rev. 9 dated 1 June 2011).
+	 * Use zeroed "index" variable as the dummy.
+	 */
+
+	index = 0;
+	lpc32xx_eth_send(dev, &index, 4);
+
+	return 0;
+}
+
+static int lpc32xx_eth_halt(struct eth_device *dev)
+{
+	struct lpc32xx_eth_device *lpc32xx_eth_device =
+		container_of(dev, struct lpc32xx_eth_device, dev);
+	struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs;
+
+	/* Reset all MAC logic */
+	writel(MAC1_RESETS, &regs->mac1);
+	writel(COMMAND_RESETS, &regs->command);
+	/* Let reset condition settle */
+	udelay(2000);
+
+	return 0;
+}
+
+#if defined(CONFIG_PHYLIB)
+int lpc32xx_eth_phylib_init(struct eth_device *dev, int phyid)
+{
+	struct mii_dev *bus;
+	struct phy_device *phydev;
+	int ret;
+
+	bus = mdio_alloc();
+	if (!bus) {
+		printf("mdio_alloc failed\n");
+		return -ENOMEM;
+	}
+	bus->read = lpc32xx_eth_phy_read;
+	bus->write = lpc32xx_eth_phy_write;
+	sprintf(bus->name, dev->name);
+
+	ret = mdio_register(bus);
+	if (ret) {
+		printf("mdio_register failed\n");
+		free(bus);
+		return -ENOMEM;
+	}
+
+	phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_MII);
+	if (!phydev) {
+		printf("phy_connect failed\n");
+		return -ENODEV;
+	}
+
+	phy_config(phydev);
+	phy_startup(phydev);
+
+	return 0;
+}
+#endif
+
+int lpc32xx_eth_initialize(bd_t *bis)
+{
+	struct eth_device *dev = &lpc32xx_eth.dev;
+	struct lpc32xx_eth_registers *regs = lpc32xx_eth.regs;
+
+	/*
+	 * Set RMII management clock rate. With HCLK at 104 MHz and
+	 * a divider of 28, this will be 3.72 MHz.
+	 */
+
+	writel(MCFG_CLOCK_SELECT_DIV28, &regs->mcfg);
+
+	/* Reset all MAC logic */
+	writel(MAC1_RESETS, &regs->mac1);
+	writel(COMMAND_RESETS, &regs->command);
+
+	/* wait 10 ms for the whole I/F to reset */
+	udelay(10000);
+
+	/* must be less than sizeof(dev->name) */
+	strcpy(dev->name, "eth0");
+
+	dev->init = (void *)lpc32xx_eth_init;
+	dev->halt = (void *)lpc32xx_eth_halt;
+	dev->send = (void *)lpc32xx_eth_send;
+	dev->recv = (void *)lpc32xx_eth_recv;
+	dev->write_hwaddr = (void *)lpc32xx_eth_write_hwaddr;
+
+	/* Release SOFT reset to let MII talk to PHY */
+	clrbits_le32(&regs->mac1, MAC1_SOFT_RESET);
+
+	/* register driver before talking to phy */
+	eth_register(dev);
+
+#if defined(CONFIG_PHYLIB)
+	lpc32xx_eth_phylib_init(dev, 0);
+#elif defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
+	miiphy_register(dev->name, mii_reg_read, mii_reg_write);
+#endif
+
+	return 0;
+}

include/netdev.h

@@ -57,6 +57,7 @@ int greth_initialize(bd_t *bis);
 void gt6426x_eth_initialize(bd_t *bis);
 int ks8851_mll_initialize(u8 dev_num, int base_addr);
 int lan91c96_initialize(u8 dev_num, int base_addr);
+int lpc32xx_eth_initialize(bd_t *bis);
 int macb_eth_initialize(int id, void *regs, unsigned int phy_addr);
 int mcdmafec_initialize(bd_t *bis);
 int mcffec_initialize(bd_t *bis);