Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE
into the console and hitting enter afterwards, causes a hang in the
system because CONFIG_SYS_PBSIZE is not capable of storing the extra
characters of the error message:
"Unknown command '' - try 'help'".

Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h
to solve this problem.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>

The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).

Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Add option to set shell prompt string from menuconfig and migrate
boards globally.

The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
  entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
  CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
  right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
  CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
  files. This results in a streamlined default value across platforms, and
  includes the following files: spear-common, sunxi-common, mv-common,
  ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
  not updated in their respective defconfig files under the assumption that
  since they did not explicitly define a value, they're fine with whatever
  the default is.
- On the other hand, boards that relied on a value defined in some
  <boards>_common.h file such as woodburn_common, rpi-common,
  bur_am335x_common, ls2085a_common, siemens_am33x_common, and
  omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
  assigning a value for CONFIG_SYS_PROMPT.

Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>

Enable SPL support for at91sam9x5ek board. Now, it supports
boot up from NAND flash and SPI flash.

Signed-off-by: Bo Shen <voice.shen@atmel.com>

This patch will save U-Boot environment as a file: uboot.env, in FAT partition
instead of saving it in raw sector of MMC card.

This make us easier to manage the environment file.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>

Now the AT91FAMILY is already defined in the at91 SoC header. The at91
board config file will include the SoC header file.

So we can remove the redundant AT91FAMILY definition in at91 board
config files.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase patch]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, move the
CONFIG_SYS_NO_FLASH to proper position, then we don't need to undef
these two commands.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

remove unneeded #undef for at91sam9x5ek board.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Get rid of too many ifdeffery in usb ohci driver

Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

remove the config.mk file
move text base define to board config file for following boards
  - at91sam9m10g45ek
  - at91sam9x5ek

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot
to flash the rootfs, in order to avoid flash one sector with all 0xff
into NAND, so use nand trimffs subcommand to avoid it

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

Change nand flash partition table according to www.at91.com/linux4sam

more information: http://www.at91.com/linux4sam/bin/view/Linux4SAM/GettingStarted#Linux4SAM_NandFlash_demo_Memory



Signed-off-by: Bo Shen <voice.shen@atmel.com>
[minor commit message changes]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Support to boot zImage

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[Add bootz for at91rm9200, at91sam9263, at91sam9rl]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Add dataflash boot support on at91sam9x5ek board

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

The mainline linux kernel is moving to flatten device tree support
Add the CONFIG_OF_LIBFDT option to support booting DT linux kernel

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Add at91sam9x5 series spi flash boot support

Using at91sam9x5ek_spiflash to configure, then it can boot from at25df321
serial flash

SPI mater work in 30Mhz speed, while not 1Mhz speed. This will base on
atmel_spi patch, or else, it will occur receive overrun

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Remove CONFIG_ARCH_CPU_INIT, no need it anymore

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Add at91sam9x5ek board support, this board support the following SoCs
  AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35

Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Enable EHCI support instead OHCI

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>

We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file.  This is used when a board has not set its
own table.

Signed-off-by: Tom Rini <trini@ti.com>

$ git grep AUTOSCRIPT
include/configs/at91sam9m10g45ek.h:#undef CONFIG_CMD_AUTOSCRIPT
include/configs/gplugd.h:#define CONFIG_CMD_AUTOSCRIPT

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Anatolij Gustschin <agust@denx.de>

NAND_MAX_CHIPS has been replaced by CONFIG_SYS_NAND_MAX_CHIPS,
and the latter defaults to 1.

Signed-off-by: Scott Wood <scottwood@freescale.com>

Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Based on earlier work by Alex Waterman <awaterman@dawning.com>.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE).  The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().

With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway.  So don't keep this relict any
longer.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>