Ugh.  I *hate* to back this change out, but these compiler flags don't
work for relocation on all versions of GCC.  I've not been able to
reproduce the environment in my setup (and hence, not been able to
find a combination that *does* work), so I've got no choice but to go
back to the old gcc flags and linker script.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This patch has been sent on:
- 29 Sep 2007

Although mips_io_port_base is currently a part of IDE command, it is quite
fundamental for MIPS I/O port access such as in[bwl] and out[bwl]. So move
it to MIPS general part, and introduce `set_io_port_base()' from Linux.

This patch is triggered by multiple definition of `mips_io_port_base' build
error on gth2 (and tb0229 also needs this fix.)

board/gth2/libgth2.a(gth2.o): In function `log_serial_char':
/home/skuribay/devel/u-boot.git/board/gth2/gth2.c:47: multiple definition of `mips_io_port_base'
common/libcommon.a(cmd_ide.o):/home/skuribay/devel/u-boot.git/common/cmd_ide.c:712: first defined here
make: *** [u-boot] Error 1

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Spartan2/3 FPGAs. The old code used "< 0" on a "char" type to test if
the most significant bit was set, which did not work on any
architecture where "char" defaulted to be an unsigned type.

Based on a patch by Angelos Manousaridis <amanous@inaccessnetworks.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Sometimes you can't reference the DDR2 controller variables.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Jason Jin <Jason.jin@freescale.com>

Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

This patch implements general ULi 526x Ethernet driver.
Until now, it is the only native Ethernet port on
MPC8610HPCD board, but it could be used on other boards
with ULi 526x Ethernet port as well.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>

This patch adds support for 1000BASE-X to functions "miiphy_speed ()" and
"miiphy_duplex()".  It also adds function "miiphy_is_1000base_x ()", which
returns non-zero iff the PHY registers are configured for 1000BASE-X.  The
"mii info" command is modified to distinguish between 1000BASE-T and -X.

Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Ben Warren <bwarren@qstreams.com>

Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Ben Warren <bwarren@qstreams.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Changed the wording to properly describe the shadowing
of the environment from ROM to RAM

Signed-off-by: Bruce Adler <bruce.adler@acm.org>

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

Signed-off-by: Vlad Lungu <vlad@comsys.ro>

The scan code of the key 'z' is 0x1d, which should be handled.

The change has be tested on NOVATEK USB keyboard and ULI PCI OHCI
controller.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>

The configuration file has already enabled USB, but it
missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB
on MPC8641HPCN can not work because of the wrong USB
register endian.

And add the USB command to U-Boot commands list.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

usb_cpu_init() configures GPS USB pins, clocks, etc. and
is required for proper operation of kernel USB subsystem.
This setup was previously done in the kernel by the fixup
code which is being removed, thus low level init must be
done by U-boot now.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

An obvious typo. Originally fixed in linkstation u-boot port.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

Since December 2003 the timer_interrupt_cpu() function in
cpu/mpc824x/interrupts.c contains what seems to be a superfluous
parameter. Remove it.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

Add ft_cpu_setup(..)-function to adapt it for use with libfdt
based on code from mpc5xxx

Sigend-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--

To get the IDS8247 board working following are done:
 - FCC2 is deactivated
 - FCC1 is activated
 - I2C is activated
 - CFI driver is activated
 - Adapted for use with LIBFDT

Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--

Wolfgang is right: It's not a good idea to set up default initial
ethernet addresses for a board, even though they belong to the local
range.

This will change the failure mode from "IT manager screams at you for
using duplicate ethernet addresses" to a nice error message explaining
that the ethernet address hasn't been set properly.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

This is a multi-part message in MIME format.

commit e6e505eae94ed721e123e177489291fc4544b7b8
Author: Justin Flammia <jflammia@savantav.com>
Date:   Mon Oct 29 17:19:03 2007 -0400

    Found a bug in the way the DHCP Request packet is built, where the IP address
    that is offered by the server is bound to prematurely. This patch is a fix of
    that bug where the IP address offered by the DHCP server is not used until
    after the DHCP ACK from the server is received.

Signed-off-by: Justin Flammia <jflammia@savantav.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>