The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been
using the same defconfig (and dts on the kernel side) for both models.
Unfortunately this does not work for the otg controller, on the M9 this
is routed to a micro-usb connector on the outside, while as on the
A1000G-quad it is connected to an usb to sata bridge.

This commit adds a new defconfig for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Before this commit the code for determining the disconnect threshold was
checking for sun4i or sun6i assuming that those where the exception and
that newer SoCs use a disconnect threshold of 2 like sun7i does.

But it turns out that newer SoCs actually use a disconnect threshold of 3
and sun5i and sun7i are the exceptions, so check for those instead.

Here are the settings from the various Allwinner SDK sources:
 sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
 sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
 sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun8i-h3:  USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);

Note this commit makes no functional changes for sun4i - sun7i, and
changes the disconnect threshold for sun8i to match what Allwinner uses.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

On some boards we need to enable the internal pull-up te reliable detect
that no card is inserted.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

netconsole had become defective over time and cleanups.
Because the feature is used very rarely nobody did take notice about this
defect.

With this patch the resulting syntax error on call will be fixed.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>

CONFIG_NET_MULTI is not used anywhere and thus can safely be removed
from the configs.

Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>

The config for pcm051 still undef'd CONFIG_USE_IRQ. This is not
needed any more since it is not defined in the whole include path
before.

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>

Fixup include/configs/unipher.h to not set CONFIG_LIB_RAND

Signed-off-by: Tom Rini <trini@konsulko.com>

NET_RANDOM_ETHADDR depends on lib/rand.c. This patch adds dependency to
Kconfig to ensure that library is also compiled.

Remove the definitions from Blackfin boards' include/configs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a83 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

Another shell scripting command that has not been moved.

Moved using tools/moveconfig.py using these settings:

CMD_SETEXPR bool n y

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

Commit 76ec988b (net: Remove all calls to net_random_ethaddr())
accidentally deleted CONFIG_TARGET_BCT_BRETTL2=y, and since then
bct-brettl2 would not build.

Since commit a26cd049 (arch: Make board selection choices
optional), Kconfig actually allows such a .config file in which no
board is selected, but the build never succeeds.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Commit 92ac5208 (net: Remove all references to CONFIG_ETHADDR
and friends) accidentally dropped #endif.  Since then, gr_ep2s60
could not build.

scripts/kconfig/conf --silentoldconfig Kconfig
  CHK     include/config.h
  GEN     include/autoconf.mk
In file included from include/config.h:5:0,
                 from ./include/common.h:18:
include/configs/gr_ep2s60.h:15:0: error: unterminated #ifndef
 #ifndef __CONFIG_H__
 ^
make[1]: *** [include/autoconf.mk] Error 1

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

This updates r8a7794 QoS to revision 0.31 for ES1 and revision 0.321 for ES2.

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This updates r8a7793 QoS to revision 0.311.

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This updates r8a7791 QoS to revision 0.411.

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This updates r8a7790 QoS to revision 0.973.
This commit can changed from KConfig to fit contents of the QoS.

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Ethernet function of Alt board can select normal and B by DIP switch
on board. But user need to set not only DIP switch but also pin function.
This adds pin function of Ethernet function B. This can select from Kconfig.

Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The chip select 1 of the NAND controller is available if you want to
use, although the pins are shared with UART port 2.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The register value should be 1, not 4.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

PH1-Pro5 includes a newer version of DDR PHY IP.  Some registers
have been added to the reserved areas.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since commit 92ac5208 (net: Remove all references to
CONFIG_ETHADDR and friends), the ethernet device on UniPhier boards
is not working because of the incorrect (all-zero) MAC address.

Enable CONFIG_NET_RANDOM_ETHADDR to generate the random one.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

One disadvantage of commit a26cd049 (arch: Make board selection
choices optional) is that Kconfig could create such an insane
.config file that no board is selected.

As PH1-Pro4 is the main stream of UniPhier SoC family, rip off the
"optional" again in favor of PH1-Pro4 as the default SoC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This file is only built for SPL.  These ifdef conditionals are
unnecessary because UniPhier platform now supports UART on SPL.
Show appropriate messages on error.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Cache coherency for SMP is cared by Linux.  In U-Boot, the secondary
CPU(s) are just sleeping.  Nothing in memory is shared with the
primary CPU.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

For the same reason as commit d0c47b3e (serial: UniPhier: use
32 bit register access), use "str" instead of "strb" for the LCR
register setting.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The business for UniPhier Soc family has been transferred from
Panasonic Corporation to Socionext Inc.

Update the SoC select menu in Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

In the Linux coding style, it is recommended to include <linux/io.h>
rather than <asm/io.h>.  Follow this trend.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

sun8i uses the same PSCI backend as sun6i, without power clamps.
Since there is no secure SRAM, the backend is placed at the end
of DRAM.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sun8i can share the PSCI backend with sun6i. Only difference
is sun8i does not have CPU power clamp controls.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Now that we have a PSCI backend for sun6i, enable it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

This adds PSCI support for sun6i. So far it only supports
the PWR_ON method.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

The PSCI code only works for sun7i. Rename it with _sun7i suffix,
and build only if building for sun7i.

This paves the way for adding PSCI support for other platforms.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

The PSCI CPU_ON code accesses quite a few registers. Document
their names to make it easier to cross reference.

Also explain "lock cpu" and "unlock cpu" as enabling/disabling
debug access.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Make sure definitions for NAND clock and DMA gate bits are the same
across boards.

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>