Also update maintainer info.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>

Also update maintainer info.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>

Move to driver model for networking on minnowmax.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Remove FAT function prototypes from the cm5200 firmware update code, and
include the relevant headers instead.

This exposes the fact that the custom prototyoe for do_fat_read() in
this file was incorrect. Rather than simply fixing the call-site, replace
do_fat_read() with fat_exists(). This removes the only use of
do_fat_read() outside of the FAT code.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.

While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Make sure SODIMM pin 87 nRESET_OUT is released properly by explicitly
setting its pin mux function to GMI. This solves some issues with e.g.
USB not being fully operational on carrier boards with USB hubs
connected to reset if U-Boot got loaded via recovery mode aka rcm.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Various clean-ups either in comments, order or spacing without any
functional impact:
- Add some comments in the device trees resp. reorder some parameters
  for consistency across all our modules.
- Sort some include files alphabetically (while leaving common.h on
  top of course).
- Streamline some comments in the configuration files and fix the
  spacing from using spaces to tabs.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

The Colibri T20's PMIC enters a sleep mode on low supply voltage < 3.0V
±2.5% (2.92...3.08V). Rising the main supply voltage again does not
bring it back to regular operation. Not even a full reset does bring
the module back. A full power cycle was required to reboot the system.
A long positive pulse on the PMICs resume pin also reboots the system
but this pin is only accessible as a test point on the module.

This patch configures the PMIC through I2C to not enter this sleep mode
plus force it to normal state upon sleep request exit should this ever
happen.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Add LCD display support defaulting to VESA VGA resolution. Different
resolutions configurable via device tree.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Allow detecting whether or not U-Boot was launched through the
recovery mode of the resp. NVIDIA SoC.

Make use of a board specific arch_misc_init() and enable the same via
CONFIG_ARCH_MISC_INIT configuration option.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

- Move the CONS_INDEX selection out of CONFIG_SYS_EXTRA_OPTIONS and
  into Kconfig proper.
- While in here, enable CONFIG_SPL_STACK_ADDR

Signed-off-by: Tom Rini <trini@konsulko.com>

Add initial support for CM-T43, an AM437x based SoM.
This support includes: serial, MMC/eMMC, NAND, USB, ETH, I2C, GPIO, DRAM
detection.

Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>

To help others with compiling and flashing ATF and u-boot add
a README for this board.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>

HiKey is the first 96boards consumer edition compliant board. It features a hi6220
SoC which has eight ARM A53 cpu's.

This initial port adds support for: -
1) Serial
2) eMMC / SD card
3) USB
4) GPIO

It has been tested with Arm Trusted Firmware running u-boot as the BL33 executable.

Notes:

eMMC has been tested with basic reading of eMMC partition into DDR. I have not
tested writing / erasing. Due to lack of clock control it won't be
running in the most performant high speed mode.

SD card slot has been tested for reading and booting kernels into DDR.
It is also currently configured to save the u-boot environment to the
SD card.

USB has been tested with ASIX networking adapter to tftpboot kernels
into DDR. On v2015.07-rc2 dhcp now works, and also USB mass storage
are correctly enumerated.

GPIO has been tested using gpio toggle GPIO4_1-3 to flash the LEDs.

Basic SoC datasheet can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf

Board schematic can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/


96Boards-Hikey-Rev-A1.pdf

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>

Remove unused external clocks and make a common definition
for all keystone platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

This is just a cosmetic change that makes
the calling of pll init code looks much cleaner.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Use common devspeed and armspeed definitions.
Also fix reading efuse bootrom register.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

There are two types of PLL for all keystone platforms:
Main PLL, Secondary PLL. Instead of duplicating the same definition
for each secondary PLL, have a common function which does
initialization for both PLLs. And also add proper register
definitions.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

This switches the Integrator boards over to using the device model
for its serial ports.

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The mailbox buffer is required to be at least 16 bytes aligned, but for
cache invalidation and/or flush it needs to be cacheline aligned.
Use ALLOC_CACHE_ALIGN_BUFFER for all mailbox buffer allocations.

Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>

Using the twl4030 keypad allows booting directly into some special boot modes,
such as recovery or fastboot. the VOL+ key will trigger a boot to recovery while
the VOL- key will trigger a boot to fastboot.

The G (gesture) key remains unused at this point.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>

In most cases, userspace will attempt to power off the device with HALT instead
of POWER_OFF, which triggers a reset instead of a proper power off from the
TWL4030. Hence, it is up to the bootloader to actually turn the device off when
there is no reason to turn it on.

A reboot identified with the OMAP reboot mode bits set is acceptable, as well as
a power on reason from either the power button, USB or charger plug.

Other cases should trigger a power off. Note that for the U-Boot reset command
to take effect, we have to fill-in the OMAP reboot bits.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>

This adds support for resetting the device on a long press on the power button.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>

This adds support for the fastboot USB gadget, including flashing to the
internal MMC and reboot to bootloader or not.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update to use Kconfig for MUSB]
Signed-off-by: Tom Rini <trini@konsulko.com>

Now that the serial number is correctly defined, we can pass it to the kernel
using the (legacy) ATAG method. It will be automatically passed via device-tree
when enabled.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>

The OMAP3 has some die-specific ID bits that we can use to give the device a
(more or less) unique serial number. This is particularly useful for e.g. USB.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>

This adds support for the omap3 reboot mode mechanism and exports the reboot
mode via an environment variable, that is used in the boot command to make it
possible to boot from the recovery partition.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>

The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.

It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.

For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part



Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>

The change adds SPL build support to Timll DevKit3250 board, the
generated SPL image can be uploaded over UART5, JTAG or stored on
NAND. SPL is designed to load U-boot image from NAND.

All new NAND chip defines in board configuration are needed by
SPL NAND "simple" framework, the framework is used to reduce
potentially duplicated code from LPC32xx SLC NAND driver.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

This change adds more peripherals to Timll DevKit3250 board, namely
MAC and SMSC phy, SLC NAND, GPIO, SPI and I2C.

Also the default serial console is changed to UART5, added an option
to pass device tree blob by means of bootm, predefined environment
variables are slightly extended and reserved space on NAND to store
user defined U-boot environment.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC

Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:

RomBOOT
>

U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)

CPU: AT91SAM9260
Crystal frequency:   18.432 MHz
CPU clock        :  198.656 MHz
Master clock     :   99.328 MHz
       Watchdog enabled
DRAM:  64 MiB
WARNING: Caches not enabled
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   macb0
Hit any key to stop autoboot:  0
U-Boot>

Signed-off-by: Heiko Schocher <hs@denx.de>

On the highbank platform the SoC's management controller firmware
will probe the DRAM modules and populates the initial device tree with
the correct values. Therefore the memory sizes in the DT are already
correct, so remove U-Boot's DRAM bank setup so the memory node is not
"fixed up" by u-boot.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <osp@andrep.de>

If enable DM PMIC and REGULATOR, we should not use original power
framework. So need to comment out the pfuze code for original power
framework, when CONFIG_DM_PMIC_PFUZE100 defined.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add composite video out support.

This only gets enabled on the Mele M3 for now, since that is were it
was tested. It will be enabled on more boards after testing.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.

Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Fix build error for socfpga_cyclone5_defconfig:

board/altera/socfpga/wrap_sdram_config.c:245:26: error: ‘RW_MGR_MEM_NUMBER_OF_RANKS’ undeclared here (not in a function)
make[2]: *** [spl/board/altera/socfpga/wrap_sdram_config.o] Error 1

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>