With entry_point now being an unsigned long we need to adapt the last
two debug prints to use %lX not %X.

Fixes: 11e1479b ("SPL: make struct spl_image 64-bit safe")
Signed-off-by: Tom Rini <trini@konsulko.com>

The variable ret was added but never set as we did not make calls to
other functions that we needed to check the return value on.

Fixes: 505cf475 ("power: change from meaningless value to error number")
Signed-off-by: Tom Rini <trini@konsulko.com>

Xilinx changes for v2017.03

- ATF handoff
- DT syncups
- gem: Use wait_for_bit(), add simple clk support
- Simple clk driver for ZynqMP
- Other small changes

The bare default entry is wrong.  Just remove it since the (real)
entry in drivers/mmc/Kconfig has "default ARM || PPC || SANDBOX".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

Move (and rename) the following CONFIG options to Kconfig:

  CONFIG_DAVINCI_MMC  (renamed to CONFIG_MMC_DAVINCI)
  CONFIG_OMAP_HSMMC   (renamed to CONFIG_MMC_OMAP_HS)
  CONFIG_MXC_MMC      (renamed to CONFIG_MMC_MXC)
  CONFIG_MXS_MMC      (renamed to CONFIG_MMC_MXS)
  CONFIG_TEGRA_MMC    (renamed to CONFIG_MMC_SDHCI_TEGRA)
  CONFIG_SUNXI_MMC    (renamed to CONFIG_MMC_SUNXI)

They are the same option names as used in Linux.

This commit was created as follows:

[1] Rename the options with the following command:

find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'

[2] Commit the changes

[3] Create entries in driver/mmc/Kconfig.
    (copied from Linux)

[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI

[5] Sort and align drivers/mmc/Makefile for readability

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

This CONFIG is not referenced from anywhere.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

Move (and rename) the following CONFIG options to Kconfig:

  CONFIG_EXYNOS_DWMMC  (renamed to CONFIG_MMC_DW_EXYNOS)
  CONFIG_HIKEY_DWMMC   (renamed to CONFIG_MMC_DW_K3)
  CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)

The "HIKEY" is a board name, so it is not suitable for the MMC
controller name.  I am following the name used in Linux.

This commit was generated as follows:

[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'

[2] Commit the changes

[3] Create the entries in drivers/mmc/Kconfig
    (with default y for EXYNOS and SOCFPGA)

[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA

[5] Sort and align drivers/mmc/Makefile for readability

[6] Clean-up doc/README.socfpga by hand

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

This commit was created as follows:

[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'

[2] create the entry for MMC_DW in drivers/mmc/Kconfig
    (the prompt and help were copied from Linux)

[3] run "tools/moveconfig.py -y MMC_DW"

[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry

[5] Clean-up doc/README.socfpga by hand

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

I am trying to make all DesignWare-based driver options prefixed
with CONFIG_MMC_DW_.

This commit was generated as follows:

find . -name .git -prune -o -type f -print | \
xargs sed -i -e 's/ROCKCHIP_DWMMC/MMC_DW_ROCKCHIP/g'

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH is defined in the socfpga_common.h,
but not referenced at all.  Remove.

Also, clean-up the README.socfpga.  CONFIG_MMC should not be defined
in the header since it was moved to Kconfig by commit c2726995
("mmc: complete unfinished move of CONFIG_MMC").  I see no grep hit
for the others.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

'-1' is absolutely meaningless value.
This patch changed from meaningless value to error number.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Some MMC drivers describe operations with the DM_MMC_OPS form, but
there are still several drivers with older implementation.  We can
not compile drivers from different groups at the same time because
the core framework is shared with #ifdef CONFIG_DM_MMC_OPS.

Every driver should have "depends on DM_MMC_OPS" (or !DM_MMC_OPS)
explicitly to express which framework it is based on.  This will
avoid enabling drivers with incompatible interface at the same time.
It is incorrect to make a driver "select DM_MMC_OPS".

While we are here, add "depends on OF_CONTROL" as well because this
driver can be configured only by Device Tree.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

It doesn't need to seperate the condition.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

Ther is no usage anywhere. It doesn't need to maintain this bit.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

The using the bitops is too easy controlling than now.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

callback function should be moved into sdhci_ops struct.
Other controller can use these ops for controlling clock or their own
specific register.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

Add the s5p_set_clock function.
It's not good that "set_mmc_clk" is assigned directly.
In future, it should be changed to use the clock framework.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

To maintain consistency, set_ios type of legacy mmc_ops changed to int.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

This quirk doesn't need anymore.
It's replaced to get_cd callback function.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

This code is used for only pic32_sdhci controller.
To remove the "#ifdef", moves to pic32_sdhci.c.
And use the get_cd callback function.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

This code is dead code..There is no usage anywhere.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

Some SoCs can have their own card dect scheme.
Then they may use this get_cd callback function after implementing init
in their drivers.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

Buswidth is depeneded on Hardware schematic.
Evne though host can support the 8bit buswidth, if hardware doesn't
support 8bit mode, it doesn't work fine.
So the buswidth mode selection leaves a matter in each SoC drivers.

On the contrary to this, hardware supports 8bit mode, but host doesn't
support it. then controller has to disable the MMC_MODE_8BIT.
(Host can check whether 8bit mode is supported or not, since V3.0)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

Move configuration option from board file to defconfig.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This patch fixes incorrect pointer on offset device in device tree blob.
When using with the component "Ethernet 1G/2.5G BASE-X PCS/PMA or SGMII"
it does not understand what type is XAE_PHY_TYPE_1000BASE_X and trying
to change frequency.

Signed-off-by: Kamensky Ivan <kamensky.ivan@mail.ru>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

MIPS no longer needs to have its own version of this macro now.

Fixes: 2a6713b0 ("move UL() macro from armv8/mmu.h into common.h")
Signed-off-by: Tom Rini <trini@konsulko.com>

Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structure the same. Support only one entry which is U-Boot in
EL2 itself. When FIT image is adopted structure generate should be data
driven.

Currently ATF is placing this structure at the beggining of OCM which is
rewriting early parts of ATF which should be unused at that time.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Using enum simplify handling of different bitstream command
types.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add a string description for SYS_VENDOR to allow configuring boards from
other vendors than just "xilinx".

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core
which fixes some silicon bugs that needed software workarounds
in Version 1.0 that was used on Zynq systems.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Adding additional compatible string for version 1.4 of the IP block.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Enable and use the clock driver routine
defined in clock driver toset required
clock appropriately.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add basic clock driver support for zynqmp which
sets the required clock for GEM controller

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

DNL numbers are not changed that's why fastboot needs to be called with
-i parameter (Xilinx vendor id).

- Show available devices
sudo fastboot -i 0x03fd devices
xilinx_zynqmp_zcu100	fastboot

- Stop fastboot and go back to U-Boot prompt
sudo fastboot -i 0x03fd continue

- Reboot the board
sudo fastboot -i 0x03fd reboot

- Get internal variables
sudo fastboot -i 0x3fd getvar bootloader-version
bootloader-version: U-Boot 2016.07-00026-g19bd53044817
sudo fastboot -i 0x3fd getvar downloadsize
downloadsize: 0x06000000
sudo fastboot -i 0x3fd getvar version
version: 0.4
(regular variables needs to have fastboot. prefix - there is also
serialno variable which should be define as serial#)

- Format SD/MMC/EMMC card
sudo fastboot -i 0x3fd oem format
- Write images to boot and Linux partition
sudo fastboot -i 0x3fd flash boot sd.img
sudo fastboot -i 0x3fd flash Linux os.img

- Creating sd.img or os.img
$ dd if=/dev/zero of=sd.img bs=1024 count=1024
$ mkfs.vfat sd.img
$ mkdir sd-mount
$ mount -o loop sd.img sd-mount
$ echo foo > sd-mount/bar
$ umount sd-mount

partitions setting should be checked by running gpt command.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0
idle state is added in this patch. References to the idle-states node are
added in all CPU nodes. Time values: entry/exit latencies and min-residency,
needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0
and Extended StateID format.

Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Fix DT binding for usb nodes. Setup correct aliases and enable dwc3
nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Just sync between version. Others zynqmp boards have this setup.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>