Rather than putting the function prototype for board_nand_init() in the one
place where it gets called, put it into nand.h so that every place that also
defines it gets the prototype.  Otherwise, errors can go silently unnoticed
such as using the wrong return value (void rather than int) when defining
the function.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>

- Add subpage write support
- Add onenand_oob_64/32 ecclayout

This has been missing and without it UBI has some incompatibilies issues
with the current (>= 2.6.27) Linux kernel version. vid_hdr_offset is
placed differently (2048 instead of 512) without this fix.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add missing markbad function
If not, it's hang when it entered the mtd->mark_bad().

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

Update OneNAND command to support bad block awareness.
Also change the OneNAND command style to better match the
NAND version.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>

The version (ver_id) was not stored in the onenand_chip structure and
because of this the continuous locking scheme could be enabled on some
chips.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dave Liu <daveliu@freescale.com>

Sync with OneNAND kernel codes

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

The x86 based version of Darwin behaves the same quirky way as the powerpc
Darwin, so only check HOSTOS when setting up Darwin workarounds.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The code in fdt_resize() to extend the fdt size to end on a page boundary
is wrong for fdt's not located at an address aligned on a page boundary.
What's even worse, the code would make actualsize shrink rather than grow
if (blob & 0xfff) was bigger than the amount of padding added by ALIGN(),
causing fdt_add_mem_rsv to fail.

Fix it by aligning end address (blob + size) to a page boundary instead.
For aligned fdt's this is equivalent to what we had before.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>

The recvfrom() function takes a socklen_t, not an int.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

lowlevel_init of SH was corrected to use the write/readXX macro.
However, there was a problem that was not able to be compiled partially.
This patch corrected this.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Fix up rsk7203 target to build successfully using out-of-tree build.

Signed-off-by: Kieran Bingham <kbingham@mpc-data.co.uk>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Update CHANGELOG.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Parallel builds would occasionally issue this build warning:

    ln: creating symbolic link `cpu/mpc824x/bedbug_603e.c': File exists

Use "ln -sf" as quick work around for the issue.

Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch adds esd's loadpci BSP command to CPCI4052 and
CPCI405AB board. This requires CONFIG_CMD_BSP and CONFIG_PRAM.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

This patch cleans up CPCI405 board support:
- wrap long lines
- unification of spaces in function calls
- remove dead code

Use correct io accessors on peripherals.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

This patch turns on the auto RS485 mode in the 2nd external
uart on PLU405 boards. This is a special mode of the used
Exar XR16C2850 uart. Because these boards only have a 485 physical
layer connected it's a good idea to turn it on by default.

Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)

- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

So that we can locate the DDR tlb start entry to the value other than 8. By
default, it is still 8.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

The IO port selection for MPC8544DS board:
 Port			cfg_io_ports
 PCIE1		0x2, 0x3, 0x4, 0x5, 0x6, 0x7
 PCIE2		0x4, 0x5, 0x6, 0x7
 PCIE3		0x6, 0x7
 This patch changes the PCIE12 and PCIE2 logic more readable.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>

PCIE2 and PCIE3 should be decided by corresponing bit in devdisr instead of
PCIE1 bit.
On MPC8572DS board, PCIE refers to PCIE1.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>

The IO port selection is not correct on MPC8572DS and MPC8544DS board.
 This patch fixes this issue.
 For MPC8572
 Port			cfg_io_ports
 PCIE1		0x2, 0x3, 0x7, 0xb, 0xc, 0xf
 PCIE2		0x3, 0x7
 PCIE3		0x7

For MPC8544
Port			cfg_io_ports
PCIE1		0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2		0x4, 0x5, 0x6, 0x7
PCIE3		0x6, 0x7
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>

Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately.  This makes the code easier to read
and understand, and facilitates mapping changes going forward.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>

Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately.  This makes the code easier to read
and understand, and facilitates mapping changes going forward.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>