This patch adds basic Tegra30 (T30) build support - no specific
board is targeted.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

These files are used by both SPL and main U-Boot.
Also made minor changes to shared Tegra code to support
T30 differences.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

These files are for code that runs on the CPU (A9) on T30 boards.
At this time, there are no T30-specific ARMV7 files. As T30-specific
run-time code is added, it'll go here.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidai.com>

This provides SPL support for T30 boards - AVP early init, plus
CPU (A9) init/jump to main U-Boot.

Some changes were made to Tegra20 cpu.c to move common routines
into tegra-common/cpu.c and reduce code duplication.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Common Tegra files are in arch-tegra, shared between T20 and T30.
Tegra30-specific headers are in arch-tegra30. Note that some of
these will be filled in as more T30 support is added (drivers,
WB/LP0 support, etc.). A couple of Tegra20 files were changed
to support common headers in arch-tegra, also.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Boards may require a different pinmux setup for DISPALY than the default one.
Add a way to call into board specific code to set this up.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>

When u-boot is compiled for PXA25x processor, pxa/start.S is calling
cpu_init_crit by BL instruction. BL is overwriting lr register so
relocate_code is going into infinite loop. This patch preservs lr
register in r12 before calling cpu_init_crit and after function returns
restores it.

Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

Troy Kisky authored 12 years ago and Stefano Babic committed 12 years ago

Use a common watchdog driver for all these cpus.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>

Mobile storage is used the CLK_DIV_FSYS3 value.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

To get exactly clock value for mmc, support the get_mmc_clk() like
set_mmc_clk().

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

The two modified lines were indented with spaces.
They are now indented with tabs.

Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

The timer may be inited in arch_cpu_init() so it is not safe to make a
bootstage mark before this is called. Arrange the code to fix this.

Note: The question was raised as to why we don't keep all archs in sync.
PowerPC doesn't have specific bootstage markers at present (although it
does use boot progress). I hope that the generic board series will solve
this problem in general, but in the meantime this is a real problem, and
only in ARM.

We now get a correct time for board_init_f:

Timer summary in microseconds:
       Mark    Elapsed  Stage
          0          0  reset
    100,000    100,000  spl_start
    848,530    748,530  board_init_f
    907,301     58,771  board_init_r
    910,478      3,177  board_init

Signed-off-by: Simon Glass <sjg@chromium.org>

SPL u-boot may call do_reset() which depends on interrupts.o and reset.o.
So make them also appear in SPL.

Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

This option displays board info after stdio is running, so that it will
appear on the LCD. If it is displayed earlier, the board info will appear
on the serial console but not on the LCD.

Here follows a blow-by-blow description.

1a. Without CONFIG_DISPLAY_BOARDINFO_LATE, on serial:

U-Boot 2011.12-02550-g037e1c5-dirty (Nov 15 2012 - 14:29:42) for SMDK5250

CPU:   S5PC520 @ 1700MHz

Board: Google Snow, rev 0
I2C:   ready
DRAM:  2 GiB Elpida DDR3 @ 800MHz
MMC:   S5P MSHC0: 0, S5P MSHC1: 1
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment

In:    mkbp-keyb
Out:   lcd
Err:   lcd
Net:   No ethernet found.
Hit any key to stop autoboot:  0
SMDK5250 #

1b. Without CONFIG_DISPLAY_BOARDINFO_LATE, on LCD (note machine info
is missing):

In:    mkbp-keyb
Out:   lcd
Err:   lcd
Net:   No ethernet found.
Hit any key to stop autoboot:  0
SMDK5250 #

2a. With CONFIG_DISPLAY_BOARDINFO_LATE, on serial:

U-Boot 2011.12-02550-g037e1c5 (Nov 15 2012 - 14:27:40) for SMDK5250

CPU:   S5PC520 @ 1700MHz
I2C:   ready
DRAM:  2 GiB Elpida DDR3 @ 800MHz
MMC:   S5P MSHC0: 0, S5P MSHC1: 1
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment

Model: Google Snow
In:    mkbp-keyb
Out:   lcd
Err:   lcd
Net:   No ethernet found.
Hit any key to stop autoboot:  0
SMDK5250 #

2b. With CONFIG_DISPLAY_BOARDINFO_LATE, on LCD (note machine info is present):

Model: Google Snow
In:    mkbp-keyb
Out:   lcd
Err:   lcd
Net:   No ethernet found.
Hit any key to stop autoboot:  0
SMDK5250 #

Since the LCD is all that a typical user sees, it is useful to display
the model there.

We may be able to rearrange things some other way one day, but at
present this seems like a convenient way of getting the required
behaviour.

Signed-off-by: Simon Glass <sjg@chromium.org>

This option delays loading of the environment until later, so that only the
default environment will be available to U-Boot.

This can address the security risk of untrusted data being used during boot.

Any time you load untrusted data you expose yourself to a bug in the
code. The attacker gets to choose the data so can sometimes carefully
craft it to exploit a bug. We try to avoid touching user-controlled
data during a verified boot unless strictly necessary. Since the
default environment is good enough in this case (or you would just
change it), this gets around the problem by just not loading the
environment.

When CONFIG_DELAY_ENVIRONMENT is defined, it is convenient to have a
run-time way of enabling loading of the environment. Add this to the
fdt as /config/delay-environment.

Note: This patch depends on http://patchwork.ozlabs.org/patch/194342/



Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>

We want to use the fdt inside board_early_init_f(), so check for its
presence earlier in the pre-reloc init sequence.

So far ARM and microblaze are the only only ones that use
CONFIG_OF_CONTROL. Microblaze does not have the same init loop, and in
particular does not have the board_early_init_f() call. So a patch for
microblaze would have no meaning.

Signed-off-by: Simon Glass <sjg@chromium.org>

It may be necessary to know where the TLB area ends as well as where it
starts. This allows board code to complete a secure memory erase without
destroying the page tables.

Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>

In Cortex-A15 architecture, when we run cache invalidate
the cache clean operation executes automatically.
So if there are any dirty cache lines before disabling the L2 cache
these will be synchronized with the main memory when
invalidate_dcache_all() runs in the last part of U-boot

The two functions after flush_dcache_all is using the stack. So this
data will be on the cache. After disable when invalidate is called the
data will be flushed from cache to memory. This corrupts the stack in
invalida_dcache_all. So this change is required to avoid the u-boot
hang.

So flush has to be done just before clearing CR_C bit

Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>

When only DP is used, we need not enable CONFIG_EXYNOS_MIPI_DSIM.
But if we do not select CONFIG_EXYNOS_MIPI_DSIM, exynos_fb.c throws
error saying exynos_mipi_dsi_init() not defined. So, we add
dummy definition for exynos_mipi_dsi_init when CONFIG_EXYNOS_MIPI_DSIM
is not defined.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

With VPLL as source clock to FIMD,
Exynos DP Initializaton was failing sometimes with unstable clock.
Changing FIMD source to MPLL resolves this issue.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Add panel_info structure required by LCD driver
and DP panel platdata for SMDK5250.
Add GPIO configuration for LCD.
Enable FIMD and DP support on SMDK5250.
DP Panel size: 2560x1600.
We use 16BPP resolution to get LCD console.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chomium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Fabio Estevam authored 12 years ago and Stefano Babic committed 12 years ago

Add workaround for the following ARM errata: 743622 and 751472.

The motivation for this change is the following kernel commit 62e4d357a
(ARM: 7609/1: disable errata work-arounds which access
secure registers), which removes the errata from multiplatform kernel.

Since imx has been converted to multiplatform in the kernel, we need to apply
such workarounds into the bootloader.

Workaround code has been taken from arch/arm/mm/proc-v7.S from 3.7.1 kernel.

Explanation of each erratum is provided at "Chip Errata for the i.MX 6Dual/6Quad"
document available at: cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Modified the arch-kirkwood header so KWGBE_PORT_SERIAL_CONTROL1_REG(x)
returns the correct address.

Originally calling KWGBE_PORT_SERIAL_CONTROL1_REG(1) returned the
address for port 0 and vice versa.

Doesn't have any knock on effects to the u-boot code as the only
time they're used is to do the same function to both addresses

Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>

This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>

Remove code such as unneeded includes or labels.
These removals have no functional effect.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>

Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().

Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).

Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>

This patch adds the device node required for USB

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Add SPI device node data for exynos.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Add sound device node data for exynos

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Api is added to decode peripheral id based on the interrupt number
of the peripheral.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Add I2C device node data for exynos

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch add pinmux settings for Exynos4 for mmc0 and mmc2

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Adds functions to extract clock frequency of Exynos4x12 IPs.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Add device tree based ethernet driver for SMC911X controller on
SMDK5250 boards.

Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch adds initial dts file for EXYNOS5250 SoC. This dts
file currently include only ethernet devices and properties. More
devices to be added in subsequent patches.
Also add the dts file for SMDK5250 board which uses the EXYNOS5250
dts file.

Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch adds gpio structure for Exynos4x12.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch adds clock structure for Exynos4x12.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch populates base addresses of Exynos4x12 registers.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>