The device trees for these boards describe PCI I/O as starting from
address zero from the device's perspective.

Placing I/O elsewhere may cause problems with certain PCI boards, and may
cause problems with Linux.

Signed-off-by: Scott Wood <scottwood@freescale.com>

At least on the "33MHz Pilot" board crystal is actually 33.3MHz.
This patch fixes "system time drifting" problem.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This is needed to update /choosen/linux,stdout-path properly.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Plus modify environment to use it and remove bootfile env variable,
it is internal and CONFIG_BOOTFILE is used for these purposes.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Current DDR setup easily causes memory corruption, this patch fixes it.

Also fix TIMING_CFG0_MRS_CYC definition.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This patch adds qe pario pins configuration for AD7843 ADC/Touchscreen
controller and FHCI (QE USB).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This is needed for BCM PHYs to work on this board.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This patch adds basic support for Broadcom BCM5481 PHY.

RXD-RXC delay quirk comes from MPC8360E-RDK BSP source, author is
Peter Barada <peterb@logicpd.com>.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

PHY drivers will use it to setup software delay between RXD and RXC
signals.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This is primarily for the early console support.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This patch adds few routines to configure serdes on 837x targets.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

..plus get rid of some #ifdefs in the .c files.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

There's no on-board RTC on the MPC8323ERDB, but there is an EEPROM.

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

The following changes are based on kernel UCC ethernet performance:

1.  Make the CSB bus pipeline depth as 4, and enable the repeat mode
2.  Optimize transactions between QE and CSB.  Added CFG_SPCR_OPT
    switch to enable this setting.

The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:

3.  CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4.  CS0_CONFIG[ODT_WR_CONFIG] set to 1.  Was a reserved setting
    previously.
5.  TIMING_CFG_1[WRREC] is changed from 3clks to 2clks  (based on
    Twr=15ns, and this was already the setting in DDR_MODE)
6.  TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
    Trp=15ns)
7.  TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
    Tras=40ns)
8.  TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
    Trcd=15ns)
9.  TIMING_CFG_1[REFREC] changed from 21 clks to 11clks.  (based on
    Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks.  (based
    on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
    on CL=3 and WL=2).

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

Use available shift/mask macros to define DDR configuration.

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware.  Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX
and other boards.  A small firwmare must be uploaded to its on-board memory
before it can be enabled.  This patch adds the code which uploads firmware
(but not the firmware itself).

Previously, this feature was provided by a U-Boot application that was
made available only on Freescale BSPs.  The VSC7385 firmware must still
be obtained separately, but at least there is no longer a need for a separate
application.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

These defines embedded the u-boot env variables and/or the bd_t structure
in the fdt blob.  The conclusion of discussion on the u-boot email list
was that embedding these in the fdt blob is not useful: there are better
ways of passing the data (in fact, the fdt blob itself replaces the
bd_t struct).

The only board that enables these is the stxxtc and they don't appear
to be used by linux.

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Flex-OneNAND is a monolithic integrated circuit with a NAND Flash array
using a NOR Flash interface. This on-chip integration enables system designers
to reduce external system logic and use high-density NAND Flash
in applications that would otherwise have to use more NOR components.

Flex-OneNAND enables users to configure to partition it into SLC and MLC areas
in more flexible way. While MLC area of Flex-OneNAND can be used to store data
that require low reliability and high density, SLC area of Flex-OneNAND
to store data that need high reliability and high performance. Flex-OneNAND
can let users take advantage of storing these two different types of data
into one chip, which is making Flex-OneNAND more cost- and space-effective.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

Include FEC specific nodes in ft_cpu_setup only if CONFIG_MPC5xxx_FEC is
defined. Systems without FEC, i.e. no FEC node in DTB, should be possible.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Jon Loeliger <jdl@freescale.com>

AX88796L is device of NE2000 compatible.
This patch support AX88796L ethernet device.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Wolfgang Denk <wd@denx.de>

There are more devices of the NE2000 base.
A present code is difficult for us to support more devices.
To support more NE2000 clone devices, separated the function.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The Blackfin on-chip MAC driver was being managed in the BF537-STAMP board
directory, but it is not board specific, so relocate it to the drivers dir
so that other Blackfin ports can utilize it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the "ssync" instruction may have hardware anomalies associated with
it, have the smc91111 driver use the SSYNC macro rather than invoking it
directly.  We workaround all the anomalies via this macro.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This patch does some shifting around of OF support on 8xx.

Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>

For historical reasons we limited the stack to 256M because some boards
could only map that much via BATS.  However newer boards are capable of
mapping more memory (for example 85xx is capble of doing up to 2G).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>