Fix:

misc.c: In function 'misc_init_r':
misc.c:210:3: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
misc.c:211:3: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
misc.c:212:3: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]

Signed-off-by: Wolfgang Denk <wd@denx.de>

add atheros ar803x phy, used on the upcoming siemens boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>

add natsemi dp83630 phy, used on the upcoming siemens boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Tom Rini <trini@ti.com>

Faraday FTMAC110 10/100Mbps supports half-word data transfer for Linux.
However it has a weird DMA alignment issue:

(1) Tx DMA Buffer Address:
    1 bytes aligned: Invalid
    2 bytes aligned: O.K
    4 bytes aligned: O.K

(2) Rx DMA Buffer Address:
    1 bytes aligned: Invalid
    2 bytes aligned: O.K
    4 bytes aligned: Invalid!!!

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Tom Rini <trini@ti.com>

Add function ksz9031_phy_extended_write and ksz9031_phy_extended_read

Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com>

Add gigabit MAC support in macb driver
  - using IP version to distinguish whether MAC is GMAC

Signed-off-by: Bo Shen <voice.shen@atmel.com>

using phylib to configure phy device in macb driver

Signed-off-by: Bo Shen <voice.shen@atmel.com>

Using CONFIG_AT91FAMILY replace #ifdeferry for atmel SoC

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>

add network support with ksz8851_16mll on at91sam9n12ek board

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>

The device interface is 16 bits wide.
All the available packets are read from the incoming fifo.

Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
[voice.shen@atmel.com: address comments from review results]
[voice.shen@atmel.com: clean up for submit]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>

Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>

commit 39695029bc15041c809df3db4ba19bd729c447fa
Author: Charles Coldwell <coldwell@ll.mit.edu>
Date:   Tue Feb 19 08:27:33 2013 -0500

    Changes to support the Xilinx 1000BASE-X phy (GTX/MGT)

Signed-off-by: Charles Coldwell <coldwell@ll.mit.edu>

Make the link-local code conform more completely with the RFC.

This will prevent ARP queries for the target (such as while it is
rebooting) from causing the device to choose a different link-local
address, thinking that its address is in use by another machine.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

Add support for Micrel PHY KSZ9031 in phylib,
including small rework for KSZ9021 to avoid
code duplication

Signed-off-by: David Andrey <david.andrey@netmodule.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Joe Herschberger <joe.hershberger@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>

tftp.c:464:17: warning: cast to restricted __be16
tftp.c:552:29: warning: cast to restricted __be16
tftp.c:640:33: warning: cast to restricted __be16
tftp.c:642:25: warning: cast to restricted __be16

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>

for use with sparse.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>

The added weak symbol must not be static.

This was introduced in 416ce623

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

SPEAr310 and SPEAr320 Ethernet interfaces share same MDIO lines to control their
respective phys. Currently there is a fixed configuration in which only a
particular MAC can use the MDIO lines.

Call an arch specific function to take control of specific mdio lines at
runtime.

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>

Do not select MIIPORT for RGMII interface

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>

This patch tackles the time out problem which leads to break the
boot process, when loading file over nfs. The patch does two things.

First of all, we just ignore messages that arrive with a rpc_id smaller
then the client id. We just interpret this messages as answers to
formaly timed out messages.

Second, when a time out occurs we double the time to wait, so that we
do not stress the server resending the last message.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>

Marvell Dove also uses mvgbe as ethernet driver, therefore add support
for Dove to reuse the current driver.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This add phylib support to the Marvell GBE driver.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This adds PHY initialization for Marvell Alaska 88E1310 PHY.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

Add ipappend support to pass network device information to the kernel.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Not all boards define an SOC.  As a result, we can't depend on that.

This was introduced in 39f98553

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

A pxelinux server setup for "default" menu is typically an x86 binary.
This does not work well with a mixed architecture setup. Extend the default
search to look for default-<arch>-<soc> and then default-<arch> before
falling back to just "default".

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

ontimeout is similar to default, but is the selection on menu timeout.
This is how cobbler sets a default. The label default is supposed to be
the default selection when <enter> is pressed. If both default and
ontimeout are set, last one parsed wins.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Menus with lots of entries and long append lines are hard to read.
Just show a numbered list using the label or name and make the choice
by entering the number.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

The prompt flag is for displaying a "boot:" prompt in pxelinux. This
doesn't make sense for u-boot as we don't support the pxelinux command
interface. So we should just ignore prompt statements and always show the
menu if a menu is present.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Standard pxelinux servers will typically use a zImage rather than u-boot
image format, so fallback to bootz if bootm fails.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Make do_bootz available for other functions like do_bootm is.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Add support for value of -1 For localboot. A value of -1 means return to
u-boot prompt.

The localboot value is often 0, so we need to distinguish the value from
localboot being selected. A value of greater than or equal to 0 means
attempt local boot command.

If localboot is selected, we don't want to try other entries.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Convert a bunch of string parameters to be const.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Get the MAC address using eth_getenv_enetaddr_by_index so that the MAC
address of ethact is used. This enables using the a NIC other than the
first one for PXE boot.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

The driver code was taken from Linux kernel source:
drivers/net/phy/icplus.c

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.

From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>

When use checkpatch.pl to check network related patch, it will report
--->8---
WARNING: networking block comments don't use an empty /* line,
use /* Comment...
---<8---

So, add --ignore NETWORKING_BLOCK_COMMENT_STYLE into .checkpatch.conf
This will help to keep all driver include network related driver use
the same comment style

Signed-off-by: Bo Shen <voice.shen@atmel.com>