Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>

This patch abstracts Kirkwood arch specific changes to support ehci-kirkwood driver

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>

This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller.  Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>

There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>

This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>

The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com

).

Signed-off-by: Stefano Babic <sbabic@denx.de>

Due to change in the usb_board_init() prototype, the USB for
the TrizepsIV was not correctly initialized.
Removed dummy print from usb_board_stop().

Signed-off-by: Stefano Babic <sbabic@denx.de>

This patch looks okay on u-boot-net.git/next branch
but when it was merged to u-boot.git/master the last line is missing

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>

This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

update against linux v2.6.30

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.

CAN is available on AT91SAM9263 and AT91CAP9 SoC.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

Correct define typo (. -> ,)

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual
NAND boot.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
CC: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.

Without this patch, EMIF configurations made in board_init()
will be invalidated.

Signed-off-by: Thomas Lange <thomas@corelatus.se>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Peter Pearse <peter.pearse@arm.com>

Kirkwood family controllers are highly integrated SOCs
based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.

SOC versions supported:-
1) 88F6281-A0       define CONFIG_KW88F6281_A0
2) 88F6192-A0       define CONFIG_KW88F6192_A0

Other supported features:-
1) get_random_hex() fucntion
2) PCI Express port initialization
3) NS16550 driver support

Contributors:
Yotam Admon <yotam@marvell.com>
Michael Blostein <michaelbl@marvell.com

Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Acked-by: Stefan Rose <sr@denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>

This patch is required for Kirkwood SoC support
may be used by other ARM architectures

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>

Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>

On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was
set to 0 after being set to 500 ms for the PHY reset.
Do backup the old reset length and restore it after the MACB initialisation.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Stelian Pop <stelian@popies.net>

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>

Because of the reset_cpu is soc specific, should be move to soc
And read reset value from SYS_ID register instead of hard code
this patch also supports s3c6410

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>

Signed-off-by: Ilya Yanok <yanok@emcraft.com>

UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>

This patch adds generic code to support Freescale's i.MX27 SoCs.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.

It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.

Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).

The patch is based on the work by Maxim Artamonov.

Signed-off-by: Maxim Artamonov <scn1874@yandex.ru>
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>

Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>

the lowlevel init sequence is the same so unify it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>