Yung-Ching LIN authored 8 years ago and Stefano Babic committed 7 years ago

Apply the proper setting for the reserved bits in SetDes Test and System Mode Control register
to avoid the voltage peak issue while we do the IEEE PHY comformance test

Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>

Yung-Ching LIN authored 8 years ago and Stefano Babic committed 7 years ago

Add the delay (10ms) to ensure the clock is stable and to meet the clock-to-reset(1ms) requirement recommended in the AR8033 datasheet

Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>

Yung-Ching LIN authored 8 years ago and Stefano Babic committed 7 years ago

Change the PMIC bulk configuration from auto mode to sync mode to avoid the voltage shutdown issue

Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>

Yung-Ching LIN authored 8 years ago and Stefano Babic committed 7 years ago

Add the configuration options for display initialization in case we need to
do the display initialization in kernel to support different timing settings

Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>

Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>

Akshay Bhat authored 8 years ago and Stefano Babic committed 8 years ago

Add support for Advantech DMS-BA16 board. The board is based on Advantech
BA16 module which has a i.MX6D processor. The board supports:
 - FEC Ethernet
 - USB Ports
 - SDHC and MMC boot
 - SPI NOR
 - LVDS and HDMI display

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6D
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: u-boot@lists.denx.de
Cc: sbabic@denx.de

Add support for Advantech SOM-DB5800 with the SOM-6867 installed.
This is very similar to conga-qeval20-qa3-e3845 in that there is a
reference carrier board (SOM-DB5800) with a Baytrail based SoM (SOM-6867)
installed.

Currently supported:
 - 2x UART (From ITE EC on SOM-6867) routed to COM3/4 connectors on
   SOM-DB5800.
 - 4x USB 2.0 (EHCI)
 - Video
 - SATA
 - Ethernet
 - PCIe
 - Realtek ALC892 HD Audio
   Pad configuration for HDA_RSTB, HDA_SYNC, HDA_CLK, HDA_SDO
   HDA_SDI0 is set in DT to enable HD Audio codec.
   Pin defaults for codec pin complexs are not changed.

Not supported:
 - Winbond Super I/O (Must be disabled with jumpers on SOM-DB8500)
 - USB 3.0 (XHCI)
 - TPM

Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>