On the P1022/P1013, the work-around for erratum SATA_A001 was implemented
only if U-Boot initializes SATA, but SATA is not initialized by default.  So
move the work-around to the CPU initialization function, so that it's always
executed on the SOCs that need it.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files.  So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020.  It was already defined for the
P1010 and P1014.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Erratum A-003474: Internal DDR calibration circuit is not supported

Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.

Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf54

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Make the fixup matchable with dts and kernel.  Update the compatible from
"fsl,flexcan-v1.0" to "fsl,p1010-flexcan" and Change the "clock-freq"
property to "clock-frequency".  We also change flexcan frequency from
CCB-clock to CCB-clock/2 according to P1010 spec.

We now keep the old interfaces to make previous kernel work. They should
be removed in the future.

Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Erratum A-003999: Running Floating Point instructions requires special
initialization.

Impact:
Floating point arithmetic operations may result in an incorrect value.

Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

common/menu.c used printf() in a number of places to print user
provided, constant strings (like the "title" string).  printf() is
dangerous here for example in case the user unwittingly embeds some
'%' caracters that printf() would interpret as formatting and then
pick up random arguments.  Use puts() instead.

We also omit the trailing ':' in the title line - if a user wants
this, he can provide it as part of the title string.

Signed-off-by: Wolfgang Denk <wd@denx.de>

* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
  MAKEALL: drop obsolete mx31pdk_nand target
  dataflash: fix parameters order in write_dataflash()
  hawkboard: Replace HAWKBOARD_KICK{0, 1}_UNLOCK defines
  davinci_sonata: define CONFIG_MACH_TYPE for davinci_sonata board
  davinci_schmoogie: define CONFIG_MACH_TYPE for davinci_schmoogie board
  arm: a320evb: define mach-type in board config file
  OMAP3: Use sdelay from arch/arm/cpu/armv7/syslib.c instead of cloning that.
  Fix Stelian's email address

* 'master' of git://git.denx.de/u-boot-video:
  DIU: 1080P and 720P support
  CFB: Fix font rendering on mx5 framebuffer

The mx31pdk can boot only from NAND and the target was
already updated in boards.cfg. mx31pdk_nand is obsolete
and is dropped.

Signed-off-by: Stefano Babic <sbabic@denx.de>

Fix parameters order in write_dataflash() function extern declaration in
the header file.
Parameters order, as in function definition, should be:
addr_dest, addr_src, size.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

This patch replaces the HAWKBOARD_KICK{0,1}_UNLOCK defines by
DV_SYSCFG_KICK{0,1}_UNLOCK.

The kick register values are not hawkboard specific but may be used
for all davinci boards. In commit f3c149d6
new defines for these values wer introduced.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>

This patch fixes the build breakage for the davinci_sonata board.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sergey Kubushyn <ksi@koi8.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>

This patch fixes the build breakage for the davinci_schmoogie board.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sergey Kubushyn <ksi@koi8.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>

MACH_TYPE_FARADAY was dropped from mach-types.h. Add it back to
board config file.

Signed-off-by: Yan-Pai Chen <ypchen@faraday-tech.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

There is no need to have such a function twice.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

* 'master' of git://git.denx.de/u-boot-mmc:
  Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec"
  mmc: mv_sdhci: Fix host version read for Armada100

As a result of the commit 68332608 the uart16550 driver
is broken for Microblaze big endian systems, because of
the missing 3 byte offset. Other than as described, not
all U-Boot BSP will treat properly the 3 byte offset.

This why prefer to mask out the 3 byte offset in general
and setup correct _REG_SIZE value depending on edianess.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Tested-by: Michal Simek <monstr@monstr.eu>

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>

cmd_nvedit.c: In function 'do_env_grep':
cmd_nvedit.c:182:3: warning: suggest parentheses around assignment used as truth value

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

Fix:

x86emu/ops2.c: In function 'x86emuOp2_set_byte':
x86emu/ops2.c:171:11: warning: variable 'name' set but not used [-Wunused-but-set-variable]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This reverts commit 02f3029f.

This patch add 3 times retry to CMD8 because the Marvell mmc controller
doesn't obey the power ramp up process in the SD specification 6.4.1.
(Please refer to figure 6.1 and 6.2 in the specification.)

The CMD0 should be send after power ramp up has been finished.
However, the Marvell mmc contorller must do power ramp up after the
first CMD0 command has been send.

This patch also affect existing platforms like Nokia N900 and other
platforms.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Acked-by: Lei Wen <leiwen@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>

sdhci_readw does not work for host version read in Armada100 series
SoCs. This patch fix this issue by making a sdhci_readl call to get host
version.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

Add the 1920x1080 and 1280x720 resolution support.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
CC: Anatolij Gustschin <agust@denx.de>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

* 'hs@denx.de' of git://git.denx.de/u-boot-staging:
  drivers/net/dnet.c: Fix GCC 4.6 warnings
  board/xaeniax/flash.c: Fix GCC 4.6 warnings
  net/bootp.c: Fix GCC 4.6 warning
  common/cmd_bootm.c: Fix GCC 4.6 warnings
  board/mx1ads/mx1ads.c: Fix GCC 4.6 warning
  board/mx1ads/syncflash.c: Fix GCC 4.6 warnings
  board/lubbock/flash.c: Fix GCC 4.6 warnings
  drivers/net/cs8900.c: Fix GCC 4.6 warning
  arch/arm/cpu/arm926ejs/omap/cpuinfo.c: Fix GCC 4.6 warnings
  drivers/net/lan91c96.c: Fix GCC 4.6 warning
  board/ronetix/pm9263/pm9263.c: Fix GCC 4.6 warning
  drivers/mtd/onenand/samsung.c: Fix GCC 4.6 warning
  drivers/usb/musb/musb_hcd.c: Fix GCC 4.6 warning

Fix:
davinci_i2c.c: In function 'flush_rx':
davinci_i2c.c:81:6: warning: variable 'dummy' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>

There are some magic constants in this drivers, which I cannot
fixup ... Eran, can you help here?

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Eran Man <eran@nbase.co.il>

This supports I2C of Renesas SH.
I tested on SH7724.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
dnet.c: In function 'dnet_send':
dnet.c:136:9: warning: variable 'len' set but not used
[-Wunused-but-set-variable]
dnet.c: In function 'dnet_set_hwaddr':
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
flash.c: In function 'flash_erase':
flash.c:223:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:392:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
bootp.c: In function 'BootpCopyNetParams':
bootp.c:108:11: warning: unused variable 'tmp_ip' [-Wunused-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
cmd_bootm.c: In function 'bootm_load_os':
cmd_bootm.c:315:7: warning: unused variable 'unc_len'
[-Wunused-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
mx1ads.c: In function 'board_early_init_f':
mx1ads.c:83:24: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
syncflash.c: In function 'SF_SR':
syncflash.c:60:10: warning: variable 'tmp1' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'SF_PrechargeAll':
syncflash.c:96:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
mx1ads.c: In function 'board_early_init_f':
mx1ads.c:83:24: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'SF_Erase':
syncflash.c:112:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'flash_init':
syncflash.c:155:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
flash.c: In function 'flash_erase':
flash.c:223:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:392:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
cs8900.c: In function 'get_reg_init_bus':
cs8900.c:69:14: warning: variable 'c' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
cpuinfo.c: In function 'print_cpuinfo':
cpuinfo.c:155:6: warning: variable 'system_serial_low' set but not used
[-Wunused-but-set-variable]
cpuinfo.c:154:6: warning: variable 'system_serial_high' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Anatolij Gustschin authored 13 years ago and Heiko Schocher committed 13 years ago

Fix:
lan91c96.c: In function 'dump_memory_info':
lan91c96.c:157:7: warning: variable 'mem_info' set but not used
[-Wunused-but-set-variable]
lan91c96.c: In function 'smc_send_packet':
lan91c96.c:320:16: warning: variable 'ioaddr' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>