Basic support for the Arcom/Eurotech Viper SBC.

Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>

arch/arm/mach-pxa/Kconfig

@@ -119,6 +119,15 @@ config MACH_TOSA
 	select PXA25x
 	select PXA_HAVE_BOARD_IRQS
 
+config ARCH_VIPER
+	bool "Arcom/Eurotech VIPER SBC"
+	select PXA25x
+	select ISA
+	select I2C_GPIO
+	select HAVE_PWM
+	select PXA_HAVE_BOARD_IRQS
+	select PXA_HAVE_ISA_IRQS
+
 config ARCH_PXA_ESERIES
 	bool "PXA based Toshiba e-series PDAs"
 	select PXA25x

arch/arm/mach-pxa/Makefile

@@ -43,6 +43,7 @@ obj-$(CONFIG_MACH_E750)		+= e750_lcd.o
 obj-$(CONFIG_MACH_E400)		+= e400_lcd.o
 obj-$(CONFIG_MACH_E800)		+= e800_lcd.o
 obj-$(CONFIG_MACH_PALMTX)	+= palmtx.o
+obj-$(CONFIG_ARCH_VIPER)	+= viper.o
 
 ifeq ($(CONFIG_MACH_ZYLONITE),y)
   obj-y				+= zylonite.o

arch/arm/mach-pxa/include/mach/viper.h

+/*
+ * arch/arm/mach-pxa/include/mach/viper.h
+ *
+ * Author:	Ian Campbell
+ * Created:	Feb 03, 2003
+ * Copyright:	Arcom Control Systems.
+ *
+ * Maintained by Marc Zyngier <maz@misterjones.org>
+ *			      <marc.zyngier@altran.com>
+ *
+ * Created based on lubbock.h:
+ *  Author:	Nicolas Pitre
+ *  Created:	Jun 15, 2001
+ *  Copyright:	MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef ARCH_VIPER_H
+#define ARCH_VIPER_H
+
+#define VIPER_BOOT_PHYS		PXA_CS0_PHYS
+#define VIPER_FLASH_PHYS	PXA_CS1_PHYS
+#define VIPER_ETH_PHYS		PXA_CS2_PHYS
+#define VIPER_USB_PHYS		PXA_CS3_PHYS
+#define VIPER_ETH_DATA_PHYS	PXA_CS4_PHYS
+#define VIPER_CPLD_PHYS		PXA_CS5_PHYS
+
+#define VIPER_CPLD_BASE		(0xf0000000)
+#define VIPER_PC104IO_BASE	(0xf1000000)
+#define VIPER_USB_BASE		(0xf1800000)
+
+#define VIPER_ETH_GPIO		(0)
+#define VIPER_CPLD_GPIO		(1)
+#define VIPER_USB_GPIO		(2)
+#define VIPER_UARTA_GPIO	(4)
+#define VIPER_UARTB_GPIO	(3)
+#define VIPER_CF_CD_GPIO	(32)
+#define VIPER_CF_RDY_GPIO	(8)
+#define VIPER_BCKLIGHT_EN_GPIO	(9)
+#define VIPER_LCD_EN_GPIO	(10)
+#define VIPER_PSU_DATA_GPIO	(6)
+#define VIPER_PSU_CLK_GPIO	(11)
+#define VIPER_UART_SHDN_GPIO	(12)
+#define VIPER_BRIGHTNESS_GPIO	(16)
+#define VIPER_PSU_nCS_LD_GPIO	(19)
+#define VIPER_UPS_GPIO		(20)
+#define VIPER_CF_POWER_GPIO	(82)
+#define VIPER_TPM_I2C_SDA_GPIO	(26)
+#define VIPER_TPM_I2C_SCL_GPIO	(27)
+#define VIPER_RTC_I2C_SDA_GPIO	(83)
+#define VIPER_RTC_I2C_SCL_GPIO	(84)
+
+#define VIPER_CPLD_P2V(x)	((x) - VIPER_CPLD_PHYS + VIPER_CPLD_BASE)
+#define VIPER_CPLD_V2P(x)	((x) - VIPER_CPLD_BASE + VIPER_CPLD_PHYS)
+
+#ifndef __ASSEMBLY__
+#  define __VIPER_CPLD_REG(x)	(*((volatile u16 *)VIPER_CPLD_P2V(x)))
+#endif
+
+/* board level registers in the CPLD: (offsets from CPLD_BASE) ... */
+
+/* ... Physical addresses */
+#define _VIPER_LO_IRQ_STATUS	(VIPER_CPLD_PHYS + 0x100000)
+#define _VIPER_ICR_PHYS		(VIPER_CPLD_PHYS + 0x100002)
+#define _VIPER_HI_IRQ_STATUS	(VIPER_CPLD_PHYS + 0x100004)
+#define _VIPER_VERSION_PHYS	(VIPER_CPLD_PHYS + 0x100006)
+#define VIPER_UARTA_PHYS	(VIPER_CPLD_PHYS + 0x300010)
+#define VIPER_UARTB_PHYS	(VIPER_CPLD_PHYS + 0x300000)
+#define _VIPER_SRAM_BASE	(VIPER_CPLD_PHYS + 0x800000)
+
+/* ... Virtual addresses */
+#define VIPER_LO_IRQ_STATUS	__VIPER_CPLD_REG(_VIPER_LO_IRQ_STATUS)
+#define VIPER_HI_IRQ_STATUS	__VIPER_CPLD_REG(_VIPER_HI_IRQ_STATUS)
+#define VIPER_VERSION		__VIPER_CPLD_REG(_VIPER_VERSION_PHYS)
+#define VIPER_ICR		__VIPER_CPLD_REG(_VIPER_ICR_PHYS)
+
+/* Decode VIPER_VERSION register */
+#define VIPER_CPLD_REVISION(x)	(((x) >> 5) & 0x7)
+#define VIPER_BOARD_VERSION(x)	(((x) >> 3) & 0x3)
+#define VIPER_BOARD_ISSUE(x)	(((x) >> 0) & 0x7)
+
+/* Interrupt and Configuration Register (VIPER_ICR) */
+/* This is a write only register. Only CF_RST is used under Linux */
+
+extern void viper_cf_rst(int state);
+
+#define VIPER_ICR_RETRIG	(1 << 0)
+#define VIPER_ICR_AUTO_CLR	(1 << 1)
+#define VIPER_ICR_R_DIS		(1 << 2)
+#define VIPER_ICR_CF_RST	(1 << 3)
+
+#endif
+