- Aug 12, 2010
-
-
Adrian Hunter authored
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4 cards can support secure erase, trim and secure trim operations that are all variants of the basic erase command. SD/MMC device attributes "erase_size" and "preferred_erase_size" have been added. "erase_size" is the minimum size, in bytes, of an erase operation. For MMC, "erase_size" is the erase group size reported by the card. Note that "erase_size" does not apply to trim or secure trim operations where the minimum size is always one 512 byte sector. For SD, "erase_size" is 512 if the card is block-addressed, 0 otherwise. SD/MMC cards can erase an arbitrarily large area up to and including the whole card. When erasing a large area it may be desirable to do it in smaller chunks for three reasons: 1. A single erase command will make all other I/O on the card wait. This is not a problem if the whole card is being erased, but erasing one partition will make I/O for another partition on the same card wait for the duration of the erase - which could be a several minutes. 2. To be able to inform the user of erase progress. 3. The erase timeout becomes too large to be very useful. Because the erase timeout contains a margin which is multiplied by the size of the erase area, the value can end up being several minutes for large areas. "erase_size" is not the most efficient unit to erase (especially for SD where it is just one sector), hence "preferred_erase_size" provides a good chunk size for erasing large areas. For MMC, "preferred_erase_size" is the high-capacity erase size if a card specifies one, otherwise it is based on the capacity of the card. For SD, "preferred_erase_size" is the allocation unit size specified by the card. "preferred_erase_size" is in bytes. Signed-off-by:Adrian Hunter <adrian.hunter@nokia.com> Acked-by:
Jens Axboe <axboe@kernel.dk> Cc: Kyungmin Park <kmpark@infradead.org> Cc: Madhusudhan Chikkature <madhu.cr@ti.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ben Gardiner <bengardiner@nanometrics.ca> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Peter Rajnoha authored
Add devname:mapper/control and MAPPER_CTRL_MINOR module alias to support dm-mod module autoloading. Signed-off-by:
Kay Sievers <kay.sievers@vrfy.org> Signed-off-by:
Peter Rajnoha <prajnoha@redhat.com> Signed-off-by:
Alasdair G Kergon <agk@redhat.com>
-
- Aug 11, 2010
-
-
Jean Delvare authored
The probe method used by i2c_new_probed_device() may not be suitable for all cases. Let the caller provide its own, optional probe function. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Acked-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Stefani Seibold authored
Simply replace the whole kfifo.c and kfifo.h files with the new generic version and fix the kerneldoc API template file. Signed-off-by:
Stefani Seibold <stefani@seibold.net> Cc: Greg KH <greg@kroah.com> Signed-off-by:
-
TAMUKI Shoichi authored
To keep panic_timeout accuracy when running under a hypervisor, the current implementation only spins on long time (1 second) calls to mdelay. That brings a good effect, but the problem is the keyboard LEDs don't blink at all on that situation. This patch changes to call to panic_blink_enter() between every mdelay and keeps blinking in spite of long spin timer mode. The time to call to mdelay is now 100ms. Even this change will keep panic_timeout accuracy enough when running under a hypervisor. Signed-off-by:
TAMUKI Shoichi <tamuki@linet.gr.jp> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Russell King <linux@arm.linux.org.uk> Acked-by:
Dmitry Torokhov <dtor@mail.ru> Cc: Anton Blanchard <anton@samba.org> Signed-off-by:
-
FUJITA Tomonori authored
DMA_xxBIT_MASK macros were marked as deprecated in June 2009. One more year is long enough, I think. Signed-off-by:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by:
-
FUJITA Tomonori authored
It was replaced with the DMA unamp state API (which can be used for any bus). Signed-off-by:
-
FUJITA Tomonori authored
Signed-off-by:
-
FUJITA Tomonori authored
Architectures implement dma_is_consistent() in different ways (some misinterpret the definition of API in DMA-API.txt). So it hasn't been so useful for drivers. We have only one user of the API in tree. Unlikely out-of-tree drivers use the API. Even if we fix dma_is_consistent() in some architectures, it doesn't look useful at all. It was invented long ago for some old systems that can't allocate coherent memory at all. It's better to export only APIs that are definitely necessary for drivers. Let's remove this API. Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: <linux-arch@vger.kernel.org> Signed-off-by:
-
Randy Dunlap authored
Fix typos & grammar. Use CPU instead of cpu in text. Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Acked-by:
Steffen Klassert <steffen.klassert@secunet.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Huang Shijie authored
The exception.txt has been removed from the Documentation directory. So update the index file for it. Signed-off-by:
Huang Shijie <shijie8@gmail.com> Signed-off-by:
-
Ben Hutchings authored
$ rm -rf build $ mkdir build $ cp .config build $ make O=build htmldocs ... xmlto: linux-2.6/build/Documentation/DocBook/media.xml does not validate (status 3) xmlto: Fix document syntax or use --skip-validation option linux-2.6/build/Documentation/DocBook/media.xml:4: warning: failed to load external entity "linux-2.6/build/Documentation/DocBook/media-entities.tmpl" We need the xmldoclinks built for any document types built from the XML sources. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Acked-by:
Andy Whitcroft <apw@canonical.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Joe Perches authored
Commit 1d794e3b ("Staging: wavelan: delete the driver") removed the source, so remove the documentation as well. Signed-off-by:
Joe Perches <joe@perches.com> Cc: Jean Tourrilhes <jt@hpl.hp.com> Acked-by:
Randy Dunlap <rdunlap@xenotime.net> Signed-off-by:
-
David Brownell authored
Be more consistent about runtime programming interface abuse warnings, which can reduce some confusion and trigger bugfixes. Based on an observation and patch from Jani Nikula. Also update doc to highlight some sleeping-call issues and to match some recent changes. Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Cc: Jani Nikula <ext-jani.1.nikula@nokia.com> Cc: "Ryan Mallon" <ryan@bluewatersys.com> Signed-off-by:
-
Roy Zang authored
Signed-off-by:
Roy Zang <tie-fei.zang@freescale.com> Cc: Jerry Huang <Chang-Ming.Huang@freescale.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Rusty Russell authored
Hey, at least it has both l's. Reported-by:
Marin Mitov <mitov@issp.bas.bg> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au>
-
- Aug 10, 2010
-
-
Randy Dunlap authored
'make htmldocs' produces errors due to missing a supporting media file, so add 'xmldoclinks' to the htmldocs dependencies so that the needed supporting file will be present. Documentation/DocBook/media.xml:4: warning: failed to load external entity "Documentation/DocBook/media-entities.tmpl" Signed-off-by:
-
Andy Shevchenko authored
MS Windows mounts removable storage in "Removal optimized mode" by default. All the writes to the media are synchronous which is achieved by setting FUA (Force Unit Access) bit in SCSI WRITE(10,12) commands. This prevents I/O requests aggregation in block layer dramatically decreasing performance. This patch brings an option to accept or ignore mentioned bit a) via specifying module parameter "nofua", or b) through sysfs entry /sys/devices/platform/_UDC_/gadget/gadget-lunX/nofua (_UDC_ is the name of the USB Device Controller driver) Patch is based on the work that was done by Denis Karpov for Maemo 5 platform. Signed-off-by:
Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Cc: Denis Karpov <ext-denis.2.karpov@nokia.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Michal Nazarewicz authored
A short documentation of the g_multi driver along with INF files for Windows XP SP3 are provided. Signed-off-by:
Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Michal Nazarewicz authored
Updated the INF file for g_serial gadget. It should work with most recent Windows systems now. Signed-off-by:
-
Michal Nazarewicz authored
Updated the INF file for the g_ether gadget. It should work with most recent Windows systems now. Signed-off-by:
-
Andrea Gelmini authored
Documentation/usb/linux.inf:66: ERROR: trailing whitespace Documentation/usb/linux.inf:67: ERROR: trailing whitespace Documentation/usb/linux.inf:98: ERROR: trailing whitespace Documentation/usb/linux.inf:99: ERROR: trailing whitespace Documentation/usb/linux.inf:115: ERROR: trailing whitespace Documentation/usb/linux.inf:116: ERROR: trailing whitespace Documentation/usb/linux.inf:120: ERROR: trailing whitespace Documentation/usb/linux.inf:121: ERROR: trailing whitespace Documentation/usb/linux.inf:122: ERROR: trailing whitespace Documentation/usb/linux.inf:123: ERROR: trailing whitespace Documentation/usb/linux.inf:144: ERROR: trailing whitespace Documentation/usb/linux.inf:145: ERROR: trailing whitespace Documentation/usb/linux.inf:146: ERROR: trailing whitespace Documentation/usb/linux.inf:147: ERROR: trailing whitespace Documentation/usb/linux.inf:158: ERROR: trailing whitespace Signed-off-by:
Andrea Gelmini <andrea.gelmini@gelma.net> Signed-off-by:
-
Andrea Gelmini authored
Documentation/usb/hotplug.txt:13: ERROR: trailing whitespace Documentation/usb/hotplug.txt:87: ERROR: trailing whitespace Signed-off-by:
-
Andrea Gelmini authored
Documentation/usb/ehci.txt:12: ERROR: trailing whitespace Signed-off-by:
-
Samium Gromoff authored
Provide MMIO32 support in 8250_early (aka earlycon) [randy.dunlap@oracle.com: fix printk format warnings] [akpm@linux-foundation.org: fix printk args some more] Signed-off-by:
Samium Gromoff <_deepfire@feelingofgreen.ru> Signed-off-by:
-
Takashi Iwai authored
Signed-off-by:Takashi Iwai <tiwai@suse.de>
-
Clemens Ladisch authored
Add documentation about the autodetection of the VIA codec models to avoid the false impression that they are not supported. Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Giel van Schijndel authored
Allow device probing to recognise the Fintek F71808E. Sysfs interface: * Fan/pwm control is the same as for F71889FG * Temperature and voltage sensor handling is largely the same as for the F71889FG - Has one temperature sensor less (doesn't have temp3) - Misses one voltage sensor (doesn't have V6, thus in6_input refers to what in7_input refers for F71889FG) For the purpose of the sysfs interface fxxxx_in_temp_attr[] is split up such that it can largely be reused. Signed-off-by:Giel van Schijndel <me@mortis.eu> Cc: Jean Delvare <khali@linux-fr.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by:
-
Chen Gong authored
Update coretemp supported CPU TjMax lists and some cleanup work. Signed-off-by:
Chen Gong <gong.chen@linux.intel.com> Cc: Rudolf Marek <r.marek@assembler.cz> Cc: Huaxu Wan <huaxu.wan@intel.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by:
-
Guenter Roeck authored
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by:
Guenter Roeck <guenter.roeck@ericsson.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: Randy Dunlap <rdunlap@xenotime.net> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Guenter Roeck authored
This driver adds support for the monitoring features of the Summit Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor. Signed-off-by:
Jonathan Cameron <jic23@cam.ac.uk> Cc: Jean Delvare <khali@linux-fr.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Kalhan Trisal authored
This driver will report the heading values in degrees to the sysfs interface. The values returned are headings . e.g. 245.6 Alan: Cleanups requested now all folded in and a sysfs description to keep Andrew happy. The sysfs description now resembles hwmon. Signed-off-by:
Kalhan Trisal <kalhan.trisal@intel.com> Reviewed-by:
Alan Cox <alan@linux.intel.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by:
-
Christoph Mair authored
This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by:
Christoph Mair <christoph.mair@gmail.com> Signed-off-by:
Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by:
-
Randy Dunlap authored
Add more information about patch descriptions. Signed-off-by:
Christoph Lameter <cl@linux-foundation.org> Signed-off-by:
-
David Rientjes authored
/proc/pid/oom_adj is now deprecated so that that it may eventually be removed. The target date for removal is August 2012. A warning will be printed to the kernel log if a task attempts to use this interface. Future warning will be suppressed until the kernel is rebooted to prevent spamming the kernel log. Signed-off-by:
David Rientjes <rientjes@google.com> Cc: Nick Piggin <npiggin@suse.de> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Balbir Singh <balbir@in.ibm.com> Signed-off-by:
-
David Rientjes authored
This a complete rewrite of the oom killer's badness() heuristic which is used to determine which task to kill in oom conditions. The goal is to make it as simple and predictable as possible so the results are better understood and we end up killing the task which will lead to the most memory freeing while still respecting the fine-tuning from userspace. Instead of basing the heuristic on mm->total_vm for each task, the task's rss and swap space is used instead. This is a better indication of the amount of memory that will be freeable if the oom killed task is chosen and subsequently exits. This helps specifically in cases where KDE or GNOME is chosen for oom kill on desktop systems instead of a memory hogging task. The baseline for the heuristic is a proportion of memory that each task is currently using in memory plus swap compared to the amount of "allowable" memory. "Allowable," in this sense, means the system-wide resources for unconstrained oom conditions, the set of mempolicy nodes, the mems attached to current's cpuset, or a memory controller's limit. The proportion is given on a scale of 0 (never kill) to 1000 (always kill), roughly meaning that if a task has a badness() score of 500 that the task consumes approximately 50% of allowable memory resident in RAM or in swap space. The proportion is always relative to the amount of "allowable" memory and not the total amount of RAM systemwide so that mempolicies and cpusets may operate in isolation; they shall not need to know the true size of the machine on which they are running if they are bound to a specific set of nodes or mems, respectively. Root tasks are given 3% extra memory just like __vm_enough_memory() provides in LSMs. In the event of two tasks consuming similar amounts of memory, it is generally better to save root's task. Because of the change in the badness() heuristic's baseline, it is also necessary to introduce a new user interface to tune it. It's not possible to redefine the meaning of /proc/pid/oom_adj with a new scale since the ABI cannot be changed for backward compatability. Instead, a new tunable, /proc/pid/oom_score_adj, is added that ranges from -1000 to +1000. It may be used to polarize the heuristic such that certain tasks are never considered for oom kill while others may always be considered. The value is added directly into the badness() score so a value of -500, for example, means to discount 50% of its memory consumption in comparison to other tasks either on the system, bound to the mempolicy, in the cpuset, or sharing the same memory controller. /proc/pid/oom_adj is changed so that its meaning is rescaled into the units used by /proc/pid/oom_score_adj, and vice versa. Changing one of these per-task tunables will rescale the value of the other to an equivalent meaning. Although /proc/pid/oom_adj was originally defined as a bitshift on the badness score, it now shares the same linear growth as /proc/pid/oom_score_adj but with different granularity. This is required so the ABI is not broken with userspace applications and allows oom_adj to be deprecated for future removal. Signed-off-by:
-
Mel Gorman authored
Add a simple post-processing script for the reclaim-related trace events. It can be used to give an indication of how much traffic there is on the LRU lists and how severe latencies due to reclaim are. Example output looks like the following Reclaim latencies expressed as order-latency_in_ms uname-3942 9-200.179000000004 9-98.7900000000373 9-99.8330000001006 kswapd0-311 0-662.097999999998 0-2.79700000002049 \ 0-149.100000000035 0-3295.73600000003 0-9806.31799999997 0-35528.833 \ 0-10043.197 0-129740.979 0-3.50500000000466 0-3.54899999999907 \ 0-9297.78999999992 0-3.48499999998603 0-3596.97999999998 0-3.92799999995623 \ 0-3.35000000009313 0-16729.017 0-3.57799999997951 0-47435.0630000001 \ 0-3.7819999998901 0-5864.06999999995 0-18635.334 0-10541.289 9-186011.565 \ 9-3680.86300000001 9-1379.06499999994 9-958571.115 9-66215.474 \ 9-6721.14699999988 9-1962.15299999993 9-10948061.125 9-2267.83199999994 \ 9-47120.9029999999 9-427653.886 9-2.6359999999404 9-632.148999999976 \ 9-476.753000000026 9-495.577000000048 9-8.45900000003166 9-6.6820000000298 \ 9-1.30500000016764 9-251.746000000043 9-383.905000000028 9-80.1419999999925 \ 9-281.160000000149 9-14.8780000000261 9-381.45299999998 9-512.07799999998 \ 9-49.5519999999087 9-167.439000000013 9-183.820999999996 9-239.527999999933 \ 9-19.9479999998584 9-148.747999999905 9-164.583000000101 9-16.9480000000913 \ 9-192.376000000164 9-64.1010000000242 9-1.40800000005402 9-3.60800000000745 \ 9-17.1359999999404 9-4.69500000006519 9-2.06400000001304 9-1582488.554 \ 9-6244.19499999983 9-348153.812 9-2.0999999998603 9-0.987999999895692 \ 0-32218.473 0-1.6140000000596 0-1.28100000019185 0-1.41300000017509 \ 0-1.32299999985844 0-602.584000000032 0-1.34400000004098 0-1.6929999999702 \ 1-22101.8190000001 9-174876.724 9-16.2420000000857 9-175.165999999736 \ 9-15.8589999997057 9-0.604999999981374 9-3061.09000000032 9-479.277000000235 \ 9-1.54499999992549 9-771.985000000335 9-4.88700000010431 9-15.0649999999441 \ 9-0.879999999888241 9-252.01500000013 9-1381.03600000031 9-545.689999999944 \ 9-3438.0129999998 9-3343.70099999988 bench-stresshig-3942 9-7063.33900000004 9-129960.482 9-2062.27500000002 \ 9-3845.59399999992 9-171.82799999998 9-16493.821 9-7615.23900000006 \ 9-10217.848 9-983.138000000035 9-2698.39999999991 9-4016.1540000001 \ 9-5522.37700000009 9-21630.429 \ 9-15061.048 9-10327.953 9-542.69700000016 9-317.652000000002 \ 9-8554.71699999995 9-1786.61599999992 9-1899.31499999994 9-2093.41899999999 \ 9-4992.62400000007 9-942.648999999976 9-1923.98300000001 9-3.7980000001844 \ 9-5.99899999983609 9-0.912000000011176 9-1603.67700000014 9-1.98300000000745 \ 9-3.96500000008382 9-0.902999999932945 9-2802.72199999983 9-1078.24799999991 \ 9-2155.82900000014 9-10.058999999892 9-1984.723 9-1687.97999999998 \ 9-1136.05300000007 9-3183.61699999985 9-458.731000000145 9-6.48600000003353 \ 9-1013.25200000009 9-8415.22799999989 9-10065.584 9-2076.79600000009 \ 9-3792.65699999989 9-71.2010000001173 9-2560.96999999997 9-2260.68400000012 \ 9-2862.65799999982 9-1255.81500000018 9-15.7440000001807 9-4.33499999996275 \ 9-1446.63800000004 9-238.635000000009 9-60.1790000000037 9-4.38800000003539 \ 9-639.567000000039 9-306.698000000091 9-31.4070000001229 9-74.997999999905 \ 9-632.725999999791 9-1625.93200000003 9-931.266000000061 9-98.7749999999069 \ 9-984.606999999844 9-225.638999999966 9-421.316000000108 9-653.744999999879 \ 9-572.804000000004 9-769.158999999985 9-603.918000000063 9-4.28499999991618 \ 9-626.21399999992 9-1721.25 9-0.854999999981374 9-572.39599999995 \ 9-681.881999999983 9-1345.12599999993 9-363.666999999899 9-3823.31099999999 \ 9-2991.28200000012 9-4.27099999994971 9-309.76500000013 9-3068.35700000008 \ 9-788.25 9-3515.73999999999 9-2065.96100000013 9-286.719999999972 \ 9-316.076000000117 9-344.151000000071 9-2.51000000000931 9-306.688000000082 \ 9-1515.00099999993 9-336.528999999864 9-793.491999999853 9-457.348999999929 \ 9-13620.155 9-119.933999999892 9-35.0670000000391 9-918.266999999993 \ 9-828.569000000134 9-4863.81099999999 9-105.222000000067 9-894.23900000006 \ 9-110.964999999851 9-0.662999999942258 9-12753.3150000002 9-12.6129999998957 \ 9-13368.0899999999 9-12.4199999999255 9-1.00300000002608 9-1.41100000008009 \ 9-10300.5290000001 9-16.502000000095 9-30.7949999999255 9-6283.0140000002 \ 9-4320.53799999994 9-6826.27300000004 9-3.07299999985844 9-1497.26799999992 \ 9-13.4040000000969 9-3.12999999988824 9-3.86100000003353 9-11.3539999998175 \ 9-0.10799999977462 9-21.780999999959 9-209.695999999996 9-299.647000000114 \ 9-6.01699999999255 9-20.8349999999627 9-22.5470000000205 9-5470.16800000006 \ 9-7.60499999998137 9-0.821000000229105 9-1.56600000010803 9-14.1669999998994 \ 9-0.209000000031665 9-1.82300000009127 9-1.70000000018626 9-19.9429999999702 \ 9-124.266999999993 9-0.0389999998733401 9-6.71400000015274 9-16.7710000001825 \ 9-31.0409999999683 9-0.516999999992549 9-115.888000000035 9-5.19900000002235 \ 9-222.389999999898 9-11.2739999999758 9-80.9050000000279 9-8.14500000001863 \ 9-4.44599999999627 9-0.218999999808148 9-0.715000000083819 9-0.233000000007451 \ 9-48.2630000000354 9-248.560999999987 9-374.96800000011 9-644.179000000004 \ 9-0.835999999893829 9-79.0060000000522 9-128.447999999858 9-0.692000000039116 \ 9-5.26500000013039 9-128.449000000022 9-2.04799999995157 9-12.0990000001621 \ 9-8.39899999997579 9-10.3860000001732 9-11.9310000000987 9-53.4450000000652 \ 9-0.46999999997206 9-2.96299999998882 9-17.9699999999721 9-0.776000000070781 \ 9-25.2919999998994 9-33.1110000000335 9-0.434000000124797 9-0.641000000061467 \ 9-0.505000000121072 9-1.12800000002608 9-149.222000000067 9-1.17599999997765 \ 9-3247.33100000001 9-10.7439999999478 9-153.523000000045 9-1.38300000014715 \ 9-794.762000000104 9-3.36199999996461 9-128.765999999829 9-181.543999999994 \ 9-78149.8229999999 9-176.496999999974 9-89.9940000001807 9-9.12700000009499 \ 9-250.827000000048 9-0.224999999860302 9-0.388999999966472 9-1.16700000036508 \ 9-32.1740000001155 9-12.6800000001676 9-0.0720000001601875 9-0.274999999906868 \ 9-0.724000000394881 9-266.866000000387 9-45.5709999999963 9-4.54399999976158 \ 9-8.27199999988079 9-4.38099999958649 9-0.512000000104308 9-0.0640000002458692 \ 9-5.20000000018626 9-0.0839999997988343 9-12.816000000108 9-0.503000000026077 \ 9-0.507999999914318 9-6.23999999975786 9-3.35100000025705 9-18.8530000001192 \ 9-25.2220000000671 9-68.2309999996796 9-98.9939999999478 9-0.441000000108033 \ 9-4.24599999981001 9-261.702000000048 9-3.01599999982864 9-0.0749999997206032 \ 9-0.0370000000111759 9-4.375 9-3.21800000034273 9-11.3960000001825 \ 9-0.0540000000037253 9-0.286000000312924 9-0.865999999921769 \ 9-0.294999999925494 9-6.45999999996275 9-4.31099999975413 9-128.248999999836 \ 9-0.282999999821186 9-102.155000000261 9-0.0860000001266599 \ 9-0.0540000000037253 9-0.935000000055879 9-0.0670000002719462 \ 9-5.8640000000596 9-19.9860000000335 9-4.18699999991804 9-0.566000000108033 \ 9-2.55099999997765 9-0.702000000048429 9-131.653999999631 9-0.638999999966472 \ 9-14.3229999998584 9-183.398000000045 9-178.095999999903 9-3.22899999981746 \ 9-7.31399999978021 9-22.2400000002235 9-11.7979999999516 9-108.10599999968 \ 9-99.0159999998286 9-102.640999999829 9-38.414000000339 Process Direct Wokeup Pages Pages Pages details Rclms Kswapd Scanned Sync-IO ASync-IO cc1-30800 0 1 0 0 0 wakeup-0=1 cc1-24260 0 1 0 0 0 wakeup-0=1 cc1-24152 0 12 0 0 0 wakeup-0=12 cc1-8139 0 1 0 0 0 wakeup-0=1 cc1-4390 0 1 0 0 0 wakeup-0=1 cc1-4648 0 7 0 0 0 wakeup-0=7 cc1-4552 0 3 0 0 0 wakeup-0=3 dd-4550 0 31 0 0 0 wakeup-0=31 date-4898 0 1 0 0 0 wakeup-0=1 cc1-6549 0 7 0 0 0 wakeup-0=7 as-22202 0 17 0 0 0 wakeup-0=17 cc1-6495 0 9 0 0 0 wakeup-0=9 cc1-8299 0 1 0 0 0 wakeup-0=1 cc1-6009 0 1 0 0 0 wakeup-0=1 cc1-2574 0 2 0 0 0 wakeup-0=2 cc1-30568 0 1 0 0 0 wakeup-0=1 cc1-2679 0 6 0 0 0 wakeup-0=6 sh-13747 0 12 0 0 0 wakeup-0=12 cc1-22193 0 18 0 0 0 wakeup-0=18 cc1-30725 0 2 0 0 0 wakeup-0=2 as-4392 0 2 0 0 0 wakeup-0=2 cc1-28180 0 14 0 0 0 wakeup-0=14 cc1-13697 0 2 0 0 0 wakeup-0=2 cc1-22207 0 8 0 0 0 wakeup-0=8 cc1-15270 0 179 0 0 0 wakeup-0=179 cc1-22011 0 82 0 0 0 wakeup-0=82 cp-14682 0 1 0 0 0 wakeup-0=1 as-11926 0 2 0 0 0 wakeup-0=2 cc1-6016 0 5 0 0 0 wakeup-0=5 make-18554 0 13 0 0 0 wakeup-0=13 cc1-8292 0 12 0 0 0 wakeup-0=12 make-24381 0 1 0 0 0 wakeup-1=1 date-18681 0 33 0 0 0 wakeup-0=33 cc1-32276 0 1 0 0 0 wakeup-0=1 timestamp-outpu-2809 0 253 0 0 0 wakeup-0=240 wakeup-1=13 date-18624 0 7 0 0 0 wakeup-0=7 cc1-30960 0 9 0 0 0 wakeup-0=9 cc1-4014 0 1 0 0 0 wakeup-0=1 cc1-30706 0 22 0 0 0 wakeup-0=22 uname-3942 4 1 306 0 17 direct-9=4 wakeup-9=1 cc1-28207 0 1 0 0 0 wakeup-0=1 cc1-30563 0 9 0 0 0 wakeup-0=9 cc1-22214 0 10 0 0 0 wakeup-0=10 cc1-28221 0 11 0 0 0 wakeup-0=11 cc1-28123 0 6 0 0 0 wakeup-0=6 kswapd0-311 0 7 357302 0 34233 wakeup-0=7 cc1-5988 0 7 0 0 0 wakeup-0=7 as-30734 0 161 0 0 0 wakeup-0=161 cc1-22004 0 45 0 0 0 wakeup-0=45 date-4590 0 4 0 0 0 wakeup-0=4 cc1-15279 0 213 0 0 0 wakeup-0=213 date-30735 0 1 0 0 0 wakeup-0=1 cc1-30583 0 4 0 0 0 wakeup-0=4 cc1-32324 0 2 0 0 0 wakeup-0=2 cc1-23933 0 3 0 0 0 wakeup-0=3 cc1-22001 0 36 0 0 0 wakeup-0=36 bench-stresshig-3942 287 287 80186 6295 12196 direct-9=287 wakeup-9=287 cc1-28170 0 7 0 0 0 wakeup-0=7 date-7932 0 92 0 0 0 wakeup-0=92 cc1-22222 0 6 0 0 0 wakeup-0=6 cc1-32334 0 16 0 0 0 wakeup-0=16 cc1-2690 0 6 0 0 0 wakeup-0=6 cc1-30733 0 9 0 0 0 wakeup-0=9 cc1-32298 0 2 0 0 0 wakeup-0=2 cc1-13743 0 18 0 0 0 wakeup-0=18 cc1-22186 0 4 0 0 0 wakeup-0=4 cc1-28214 0 11 0 0 0 wakeup-0=11 cc1-13735 0 1 0 0 0 wakeup-0=1 updatedb-8173 0 18 0 0 0 wakeup-0=18 cc1-13750 0 3 0 0 0 wakeup-0=3 cat-2808 0 2 0 0 0 wakeup-0=2 cc1-15277 0 169 0 0 0 wakeup-0=169 date-18317 0 1 0 0 0 wakeup-0=1 cc1-15274 0 197 0 0 0 wakeup-0=197 cc1-30732 0 1 0 0 0 wakeup-0=1 Kswapd Kswapd Order Pages Pages Pages Instance Wakeups Re-wakeup Scanned Sync-IO ASync-IO kswapd0-311 91 24 357302 0 34233 wake-0=31 wake-1=1 wake-9=59 rewake-0=10 rewake-1=1 rewake-9=13 Summary Direct reclaims: 291 Direct reclaim pages scanned: 437794 Direct reclaim write sync I/O: 6295 Direct reclaim write async I/O: 46446 Wake kswapd requests: 2152 Time stalled direct reclaim: 519.163009000002 ms Kswapd wakeups: 91 Kswapd pages scanned: 357302 Kswapd reclaim write sync I/O: 0 Kswapd reclaim write async I/O: 34233 Time kswapd awake: 5282.749757 ms Signed-off-by:
Mel Gorman <mel@csn.ul.ie> Acked-by:
Rik van Riel <riel@redhat.com> Acked-by:
Larry Woodman <lwoodman@redhat.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Chris Mason <chris.mason@oracle.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Michael Rubin <mrubin@google.com> Signed-off-by:
-
David Rientjes authored
The oom killer tasklist dump, enabled with the oom_dump_tasks sysctl, is very helpful information in diagnosing why a user's task has been killed. It emits useful information such as each eligible thread's memory usage that can determine why the system is oom, so it should be enabled by default. Signed-off-by:
KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by:
-
- Aug 09, 2010
-
-
Al Viro authored
Signed-off-by:Al Viro <viro@zeniv.linux.org.uk>
-
Christoph Hellwig authored
Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
