Here's a patch adding me to the maintainers file for the pci
hotplug subsystem, as we discussed.

Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation.  Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively.  Many people have come to expect this naming.  Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations).  I also have reports that various Sun and HP servers
have similar behavior.


Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also).  2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.

On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1.  If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.

A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.

-[0000:00]-+-00.0  Intel Corporation 5000P Chipset Memory Controller Hub
           +-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0  Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
           +-1c.0-[0000:01-02]----00.0-[0000:02]----00.0  Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)


Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.


Solution:

The solution can come in multiple steps.

Suggested fix #1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels.  It adds two new
command line options:
  pci=bfsort
  pci=nobfsort
to force the sort order, or not, as you wish.  It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".


Suggested fix #2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in.  I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first.  It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.

Suggested fix #3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order.  This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers).  I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.


Feedback appreciated.  Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.

You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm.  I think
that's both safe and appropriate in this instance.


Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

cpcihp_generic module requires configured "bridge" module parameter.
But it can be loaded successfully without that parameter.
Because module init call ends up returning positive value.

This patch prevents from loading without setting "bridge" module parameter.

Signed-off-by: Akinbou Mita <akinobu.mita@gmail.com>
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In order to finish converting to pci_get_* interfaces we need to add a couple
of bits of missing functionaility

pci_get_bus_and_slot() provides the equivalent to pci_find_slot()
(pci_get_slot is already taken as a name for something similar but not the
same)

pci_get_device_reverse() is the equivalent of pci_find_device_reverse but
refcounting

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Update MSI-HOWTO.txt according to pci_msi_supported().

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Improve pci_msi_supported() comments.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1. ioremap must be balanced by an iounmap and failing to do so can
   result in a memory leak.
2. Handle return value correctly

Tested (compilation only) with:
- allmodconfig

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch removes unnecessary cmd_busy member from struct
controller. Read command status register instead of using cmd_busy.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes the problem that shpchp driver could mis-detect
command failures if the system was under heavy load.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

pci_find is not hotplug safe, so it really doesn't want to be in an
actual hotplug driver either.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

On Thu, 2006-09-28 at 03:42, Olaf Hering wrote:
> PCI-Express AER implemetation: pcie_portdrv error handler
> 
> This patch breaks if CONFIG_PM is not enabled,
> pcie_portdrv_restore_config() will be undefined.
I move the definition of pcie_portdrv_restore_config
out of CONFIG_PM.

Below patch is against 2.6.18-mm1. Could you try it?

Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The ACPIPnP implementation had the understanding of Linux resource flags very
wrong, resulting in a nonfunctional implementation of DMA resource
allocation.

This was usually not a problem, since almost no on-board PnP devices use ISA
DMA, with the exception of ECP parallel ports. Even with that, parallel port
DMA is preconfigured by the BIOS, so this routine isn't normally called.

Except in the case where somebody does 'rmmod parport_pc; modprobe
parport_pc', where the rmmod case disables the ECP parallel port resources,
and they need to be enabled again to initialize the module. This didn't
work, resulting in a non-printing printer.

The application doing exactly the above to force reprobing of printers is
the YaST printer module. Thus without this fix YaST wedged the printer when
configuring it, and was not able to print a test page.

Reported-by: Ralf Flaxa <rf@suse.de>
Reproduced-by: Jiri Dluhos <jdluhos@suse.cz>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

pci_fixup_video turns into generic code because there are many platforms need this fixup
for embedded VGA as well as x86. The Video BIOS integrates into System BIOS on a machine
has embedded VGA although embedded VGA generally don't have PCI ROM. As a result,
embedded VGA need the way that the sysfs rom points to the Video BIOS of System
RAM (0xC0000). PCI-to-PCI Bridge Architecture specification describes the condition whether
or not PCI ROM forwards VGA compatible memory address. fixup_video suits this specification.
Although the Video ROM generally implements in x86 code regardless of platform, some
application such as X Window System can run this code by dosemu86. Therefore,
pci_fixup_video should turn into generic code.


Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

__must_check goes on the declaration, not the definition.

Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The most recent VIA IRQ quirk changes have broken various VIA devices for
some users.  We are not able to add these devices to the blacklist as they
are also available in PCI-card form, and running the quirk on these devices
brings us back to square one (running the VIA quirk on non-VIA boards where
the quirk is not needed).

This patch, based on suggestions from Sergey Vlasov, implements a scheme
similar to but more restrictive than the scheme we had in 2.6.16 and
earlier.  It runs the quirk on all VIA hardware, but *only* if a VIA
southbridge was detected on the system.

To further reduce the amount of quirked devices, this patch includes a
change suggested by Linus at http://lkml.org/lkml/2005/9/27/113

 This
ensures that devices bound to non-legacy IO-APIC interrupt lines are not
quirked.  We have made one change to Linus' suggestion: we do a comparison
of ">15" rather than ">=15", as 15 is still in the legacy interrupt range.

There is still a downside to this patch: if the user inserts a VIA PCI card
into a VIA-based motherboard, in some circumstances the quirk will also run
on the VIA PCI card.  This corner case is hard to avoid.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this was spotted by coverity (cid #819). We dereference p_slot
earlier in the function, and i found no way it could become NULL
anywhere.

Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes the problem that system will panic if multiple power
on/off operations are issued to the same slot in parallel. This
problem can be easily reproduced by commands below.

    # while true; do echo 1 > power; echo 0 > power; done &
    # while true; do echo 1 > power; echo 0 > power; done &

The cause is lack of locking for enable/disable operations. This patch
fixes this problem.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The slot number displayed in info messages would cause a confusion
because those are displayed in several ways (decimal and hex).
Furthermore, those slot number is not same as slot name (directory
name). This patch fixes those improper info messages.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes the problem that issuing SHPC command in poll mode
always fails with the following message.

        shpchp: Command not completed in 2000 msec

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a typo to make kernel compilable when floppy driver
for Sparc is build.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds profiling support to the sparc architecture. It is a
copy of the sparc64 implementation.

Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not be calling kernel_execve() directly and this
causes module build failures because kernel_execve() is not
exported to modules.

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For Hummingbird PCI controllers, we should create the root
PCI memory space resource as the full 4GB area, and then
allocate the IOMMU DMA translation window out of there.

The old code just assumed that the IOMMU DMA translation base
to the top of the 4GB area was unusable.  This is not true on
many systems such as SB100 and SB150, where the IOMMU DMA
translation window sits at 0xc0000000->0xdfffffff.

So what would happen is that any device mapped by the firmware
at the top section 0xe0000000->0xffffffff would get remapped
by Linux somewhere else leading to all kinds of problems and
boot failures.

While we're here, report more cases of OBP resource assignment
conflicts.  The only truly valid ones are ROM resource conflicts.

Signed-off-by: David S. Miller <davem@davemloft.net>

Unused, but still allow the '-s' boot option to be passed
down to init.

Based upon patches by Martin Habets.

Signed-off-by: David S. Miller <davem@davemloft.net>

It would fail the compile due to the newly added error checking testing
a bad macro for a "return value" unless USB_GADGET_DEBUG_FILES was
enabled.

Pointed out by Stephen Hemminger.

Acked-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
  USB: Add device id for Sierra Wireless MC8755
  USB: cleanup sierra wireless driver a bit
  USB: Sierra Wireless driver update
  USB: ftdi_sio whitespace fixes
  USB-SERIAL:cp2101 Add new device ID
  USB/gadget/net2280: handle sysfs errors
  usbtouchscreen: fix data reading for ITM touchscreens
  UEAGLE: fix ueagle-atm Oops
  USB: xpad: dance pad support
  USB: input: extract() and implement() are bit field manipulation routines
  USB: Memory leak in drivers/usb/serial/airprime.c
  USB Storage: unusual_devs.h entry for Sony Ericsson P990i
  USB: fix usbatm tiny race
  USB: unusual_devs entry for Nokia 6234
  USB: mos7840.c: fix a check-after-dereference
  USB: ftdi-elan.c: remove dead code
  USB: Mitsumi USB FDD 061M: UNUSUAL_DEV multilun fix
  USB: fix dereference in drivers/usb/misc/adutux.c
  USB: add USB serial mos7720 driver
  USB: move trancevibrator.c to the proper usb directory
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mthca: Use mmiowb after doorbell ring
  IB/ipath: Initialize diagpkt file on device init only
  RDMA/amso1100: Fix a NULL dereference in error path
  RDMA/amso1100: pci_module_init() conversion

Adds the device id used by the UMTS cards in Lenovo X60s notebooks sold
in Europe.

Signed-off-by: Jan Luebbe <jluebbe@lasnet.de>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This saves over 30 lines and fixes a warning from sparse and allows
debugging to work dynamically like all other usb-serial drivers.

Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The largest feature in this patch is that it adds significant throughput
increase to the Sierra driver and adds support for modem status line
control (e.g. the DTR line). This patch also updates the current sierra.c
driver so that it supports both 3-port Sierra devices and 1-port legacy
devices and removes Sierra's references in other related files (Kconfig and
airprime.c).

Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Whitespace fixups for drivers/usb/serial/ftdi_sio.c ...
removing end-of-line whitespace, and space-before-tab.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds device ID 0xEA61. This is another factory default ID
used by SILabs.

Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ITM devices seem to report only garbage when not touched. update usbtouchscreen
to do data reading like itmtouch. also fix wrong mask on pressure bits.

Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The array of attribute passed to sysfs_create_group() must be
NULL-terminated.

The sysfs entries are created before the start of the modem state machine
to avoid to stop it in case of errors in sysfs creation.  Also
{destroy,create}_fs_entries are removed as they do nothing.

Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Adds support for dance pads to the xpad driver. Dance pads require the
d-pad to be mapped to four buttons instead of two axes, so that
combinations of up/down and left/right can be hit simultaneously.
Known dance pads are detected, and there is a module parameter added
to default unknown xpad devices to map the d-pad to buttons if this is
desired. (dpad_to_buttons). Minor modifications were made to port the
changes in the original patch to a newer kernel version.

This patch was originally from Dominic Cerquetti originally written
for kernel 2.6.11.4, with minor modifications (API changes for USB,
spelling fixes to the documentation added in the original patch) made
to apply to the current kernel. I have modified Dominic's original
patch per some suggestions from Dmitry Torokhov. (There was nothing
in the patch format description about multiple From: lines, so I
haven't added myself.)

[akpm@osdl.org: cleanups]
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>