This board has not been converted to DM_SERIAL by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>

This board has not been converted to DM_SERIAL by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>

Add initial DTS support for AM571-IDK evm.

Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

BeagleBoard-X15 Rev B1 with SR1.1 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev B1 variants.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

DRA71-evm uses LP873x regulator. Enable lp873x PMIC config options.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Enable pmic/regulator config options.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Enable DM_ETH for hs boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Add DT support for dra71-evm and built it as part of FIT image.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

We are tight on space on this board so drop SPL_OS_BOOT

Signed-off-by: Tom Rini <trini@konsulko.com>

Currently, CMD_PXE is forcibly enabled in config_distro_defaults.h, so
that general purpose distributions can rely on it being defined. This
header is included, under conditions or not, by various archs or
famillies of archs / SoCs.

However, it is very possible that boards based on those SoCs will not
have a physical ethernet connector at all, even if the have a MAC; for
example, the Nanopi Neo AIR (sunxi H3) does not. It is also possible
that network booting is absolutely not necessary for a device.

However, it is not possible to disable the PXE command, as it is
forcibly enabled and is non-configurable.

But it turns out we already have a config option to build a distro-ready
image, in the name of DISTRO_DEFAULTS.

Move CMD_PXE out of the hard-coded config_distro_defaults.h into a
Kconfig option, that gets selected by DISTRO_DEFAULTS when it is set.

Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Joe Hershberger <joe.hershberger@ni.com>
[trini: Make it select MENU, run moveconfig.py]
Signed-off-by: Tom Rini <trini@konsulko.com>

A number of platforms had been using the distro default feature before
it was moved to Kconfig but did not enable the new Kconfig option when
it was enabled.  This caused a regression in terms of features and this
introduces breakage when more things move to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>

Also convert MENU while we're in here.

Signed-off-by: Tom Rini <trini@konsulko.com>

NAND SPL boot was missing. Add it. The README specific to omapl138-lcdk
is also removed because its content does not apply anymore, i.e. the
generated AIS image can be flashed directly to the NAND without
using any external tool to create and bootable AIS image.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Set the correct CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR value in order
to be able to boot from MMC/SD.

The SPL is stored at sector 0x75, while u-boot will follow at
sector 0xb5.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

An issue in the TI secure image generation tool causes the ROM to
load the SPL at a different load address than what is specified by
CONFIG_ISW_ENTRY_ADDR while doing a peripheral boot.

This causes the SPL to fail on secure devices during peripheral
boot.

The TI secure image generation tool has been fixed so that the SPL
will always be loaded at 0x403018E0 by the ROM code for both
peripheral and memory boot modes. am43x hs defconfig file have been
updated to reflect this change.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

CONFIG_RTL8139 was moved to a board defconfig by a commit 86e9dc86
("net: Move CONFIG_RTL8139 to Kconfig"), however it was done
incorrectly due to a missing CONFIG_NETDEVICES selection, thus
virtually it was just a removal of the driver compilation.

As an unlucky consequence the option was completely removed by a purge
commit adad96e6 ("configs: Re-sync HUSH options"), restore the
driver inclusion back.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

AM57xx GP EVM has USB2 port of the SoC exposed as
USB client port.

It is useful to be able to use this port for USB
DFU downloads.

Enable USB DFU support. Tested on AM57x GP EVM Rev
A3 using DFU to download to connected SD card.

configs for HS version of the AM57x EVM are
included in the patch but not really tested.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>

Without this change we see:
../arch/arm/cpu/arm926ejs/mxs/mxs.c: In function ‘print_cpuinfo’:
../arch/arm/cpu/arm926ejs/mxs/mxs.c:181:23: warning: unused variable ‘data’ [-Wunused-variable]
../arch/arm/cpu/arm926ejs/mxs/mxs.c:180:6: warning: variable ‘cpurev’ set but not used [-Wunused-but-set-variable]

So the easy solution is to disable CONFIG_DISPLAY_CPUINFO

Reviewed-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Christoph Fritz authored 8 years ago and Stefano Babic committed 8 years ago

This patch adds initial support for Samtec VIN|ING 2000 board.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>

Angus Ainslie authored 8 years ago and Stefano Babic committed 8 years ago

Enable the escpi3 nets attached to the mikroBUS slot
on the i.MX7 Sabre evalution board. Also enble the SPI flash
commands to work with the "flash click" board.

This is V2 of this patch with changes recommended by the maintainer

CC: Jagan Teki <jteki@openedev.com>

Breno Lima authored 8 years ago and Stefano Babic committed 8 years ago

UDOO Neo Board is a development board from Seco that has three models:
 - UDOO Neo Basic
 - UDOO Neo Basic Kick Starter
 - UDOO Neo Extended
 - UDOO Neo Full

All versions are based on the i.MX6 SoloX processor.

For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/

This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
https://github.com/fmntf/u-boot/commit/877b71184a5105e708024f232d36aed574961844



Only tested on the UDOO Neo Full board.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Sebastien Bourdelin authored 8 years ago and Stefano Babic committed 8 years ago

This commit adds basic support including:
MMC, Serial console

Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Eric Nelson authored 8 years ago and Stefano Babic committed 8 years ago

The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.

Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.

Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.

Signed-off-by: Eric Nelson <eric@nelint.com>

This patch removes use of U_BOOT_DEVICE in board/raspberrypi/rpi/rpi.c,
enables OF_CONTROL in the config and adjusts the rpi_*defconfig configs.

Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Introduce USB Gadget config option. This allows to combine Makefile
entries for SPL_USBETH_SUPPORT and SPL_DFU_SUPPORT.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Ravi Babu <ravibabu@ti.com>

With our common code in place actually make use of it across all our
modules.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>

Deactivate CONFIG_DISPLAY_BOARDINFO in favour of
CONFIG_DISPLAY_BOARDINFO_LATE which also displays on the LCD.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>

Add board support for sun8i_r16 Nintendo NES Classic edition.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

And also remove it from scripts/config_whitelist.txt as the
Mele_M5_defconfig was the only one defining it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Use the already available Kconfig option for AHCI. Tested on the
BananaPi.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Today we can compile a self-contained hello world efi test binary that
allows us to quickly verify whether the EFI loader framwork works.

We can use that binary outside of the self-contained test case though,
by providing it to a to-be-tested system via tftp.

This patch separates compilation of the helloworld.efi file from
including it in the u-boot binary for "bootefi hello". It also modifies
the efi_loader test case to enable travis to pick up the compiled file.
Because we're now no longer bloating the resulting u-boot binary, we
can enable compilation always, giving us good travis test coverage.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

This adds support for the Asus Chromebook Flip, an RK3288-based clamshell
device which can flip into 'tablet' mode. The device tree file comes from
Linux v4.8. The SDRAM parameters are for 4GB Samsung LPDDR3.

Signed-off-by: Simon Glass <sjg@chromium.org>

This adds support for the Asus Chromebit, and RK3288-based device designed
to plug directly into an HDMI monitor. The device tree file comes from
Linux v4.8.

Signed-off-by: Simon Glass <sjg@chromium.org>

At present we have a single rk3288-based Chromebook: chromebook_jerry. But
all such Chromebooks can use the same binary with only device-tree
differences. The family name is 'veyron', so rename the files accordingly.

Also update the device-tree filename since this currently differs from
Linux.

Signed-off-by: Simon Glass <sjg@chromium.org>

Adjust jerry to use of-platdata like other rk3288 boards. This reduces the
SPL size enough that it boots again.

Signed-off-by: Simon Glass <sjg@chromium.org>

usb host vbus power is using gpio fix regulator, enable it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

rk3036 using dwc2 usb controller, need enable relate configs for it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

PWM_ROCKCHIP need to enable for PWM regulator, this config
is missing during rebase and new patch set in previous submission.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

Use CONFIG_ARCH_T4240 from Kconfig instead.

Signed-off-by: York Sun <york.sun@nxp.com>