This patch fixes compilation error
cmd_usb.c: In function 'do_usb':
cmd_usb.c:552: error: void value not ignored as it ought to be

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Dave Liu <daveliu@freescale.com>

add simple libata support in u-boot

Signed-off-by: Dave Liu <daveliu@freescale.com>

original ata_piix driver is using IDE framework, not real
SATA framework. For now, the ata_piix driver is only used
by x86 sc520_cdp board. This patch makes the ata_piix driver
use the new SATA framework, so

- remove the duplicated command stuff
- remove the CONFIG_CMD_IDE define in the sc520_cdp.h
- add the CONFIG_CMD_SATA define to sc520_cdp.h

Signed-off-by: Dave Liu <daveliu@freescale.com>

- add the SATA framework
- add the SATA command line

Signed-off-by: Dave Liu <daveliu@freescale.com>

move the sata.h from include/ to drivers/block/ata_piix.h

Signed-off-by: Dave Liu <daveliu@freescale.com>

move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.

Signed-off-by: Dave Liu <daveliu@freescale.com>

This patch fixes compilation error
cmd_usb.c: In function 'do_usb':
cmd_usb.c:552: error: void value not ignored as it ought to be

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>

The following changes are needed to be inline with ePAPR v0.81:

* r4, r5 and now always set to 0 on boot release
* r7 is used to pass the size of the initial map area (IMA)
* EPAPR_MAGIC value changed for book-e processors
* changes in the spin table layout
* spin table supports a 64-bit physical release address

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Each file that can be built here now follows some
CONFIG_ option so that they are appropriately built
or not, as needed.  And CONFIG_ defines were added
to various board config files to make sure that happens.

The other board/freescale/*/Makefiles no longer need
to reach up and over into ../common to build their
individually needed files any more.

Boards that are CDS specific were renamed with cds_ prefix.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

get_ddr_freq() and get_bus_freq() used get_sys_info() each time they were
called.  However, get_sys_info() recalculates extraneous information when
called each time.  Have get_ddr_freq() and get_bus_freq() return memoized
values from global_data instead.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

FSL has taken to using SVR[16:23] as an SOC sub-version field.  This
is used to distinguish certain variants within an SOC family.  To
account for this, we add the SVR_SOC_VER() macro, and update the SVR_*
constants to reflect the larger value.  We also add SVR numbers for all
of the current variants.  Finally, to make things neater, rather than
use an enormous switch statement to print out the CPU type, we create
and array of SVR/name pairs (using a macro), and print out the CPU name
that matches the SVR SOC version.

Signed-off-by: Andy Fleming <afleming@freescale.com>

Signed-off-by: Andy Fleming <afleming@freescale.com>

Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.

Added support for using the ePAPR defined spin-table mechanism on 85xx.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

When we go to 36-bit physical addresses we need to keep the concept of
the physical CCSRBAR address seperate from the virtual one.

For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

With the original value of 1/2 clock cycle delay, the system ran relatively
stable except when we run benchmarks that are intensive users of memory.
When I run samba connected disk with a HDBENCH test, the system locks-up
or reboots sporadically.

Signed-off by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>

The device trees for these boards describe PCI I/O as starting from
address zero from the device's perspective.

Placing I/O elsewhere may cause problems with certain PCI boards, and may
cause problems with Linux.

Signed-off-by: Scott Wood <scottwood@freescale.com>

At least on the "33MHz Pilot" board crystal is actually 33.3MHz.
This patch fixes "system time drifting" problem.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This is needed to update /choosen/linux,stdout-path properly.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Plus modify environment to use it and remove bootfile env variable,
it is internal and CONFIG_BOOTFILE is used for these purposes.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Current DDR setup easily causes memory corruption, this patch fixes it.

Also fix TIMING_CFG0_MRS_CYC definition.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This is needed for BCM PHYs to work on this board.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This is primarily for the early console support.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

This patch adds few routines to configure serdes on 837x targets.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

There's no on-board RTC on the MPC8323ERDB, but there is an EEPROM.

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

The following changes are based on kernel UCC ethernet performance:

1.  Make the CSB bus pipeline depth as 4, and enable the repeat mode
2.  Optimize transactions between QE and CSB.  Added CFG_SPCR_OPT
    switch to enable this setting.

The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:

3.  CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4.  CS0_CONFIG[ODT_WR_CONFIG] set to 1.  Was a reserved setting
    previously.
5.  TIMING_CFG_1[WRREC] is changed from 3clks to 2clks  (based on
    Twr=15ns, and this was already the setting in DDR_MODE)
6.  TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
    Trp=15ns)
7.  TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
    Tras=40ns)
8.  TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
    Trcd=15ns)
9.  TIMING_CFG_1[REFREC] changed from 21 clks to 11clks.  (based on
    Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks.  (based
    on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
    on CL=3 and WL=2).

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

Use available shift/mask macros to define DDR configuration.

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware.  Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX
and other boards.  A small firwmare must be uploaded to its on-board memory
before it can be enabled.  This patch adds the code which uploads firmware
(but not the firmware itself).

Previously, this feature was provided by a U-Boot application that was
made available only on Freescale BSPs.  The VSC7385 firmware must still
be obtained separately, but at least there is no longer a need for a separate
application.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>

These defines embedded the u-boot env variables and/or the bd_t structure
in the fdt blob.  The conclusion of discussion on the u-boot email list
was that embedding these in the fdt blob is not useful: there are better
ways of passing the data (in fact, the fdt blob itself replaces the
bd_t struct).

The only board that enables these is the stxxtc and they don't appear
to be used by linux.

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

This patch does some shifting around of OF support on 8xx.

Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>

Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>